Jaime Lazaro Nebreda

Dr. Jaime Lazaro Nebreda

Brunel University London, London, City of London, UK
orcid

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2020 in Materials Science and Engineering: A
Verified
Journal Article
Closed access
ELEwan Lordan
Ewan Lordan
Jaime Lazaro NebredaJaime Lazaro Nebreda
Jaime Lazaro Nebreda
YZYijie Zhang
Yijie Zhang
KDKun Dou
Kun Dou
PBPaul Blake
Paul Blake
ZFZhongyun Fan
Zhongyun Fan

23 October 2009 in Advanced Engineering Materials
Verified
Journal Article
Closed access
PDF file
ESEusebio Solórzano
Eusebio Solórzano
Miguel Angel Rodríguez-PérezMiguel Angel Rodríguez-Pérez
Miguel Angel Rodríguez-Pérez
Jaime Lazaro NebredaJaime Lazaro Nebreda
Jaime Lazaro Nebreda
JSJosé Antonio de Saja
José Antonio de Saja

1 August 2021 in Journal of Materials Processing Technology
Verified
Journal Article
Open access
Jaime Lazaro NebredaJaime Lazaro Nebreda
Jaime Lazaro Nebreda
JPJayesh B. Patel
Jayesh B. Patel
ZFZhongyun Fan
Zhongyun Fan

28 June 2018 in JOM
Verified
Journal Article
Open access
PDF file
Yijie ZhangYijie Zhang
Yijie Zhang
JPJayesh Patel
Jayesh Patel
Jaime Lazaro NebredaJaime Lazaro Nebreda
Jaime Lazaro Nebreda
Zhongyun FanZhongyun Fan
Zhongyun Fan
To promote mechanical properties and reduce the performance instability of A380 alloy produced by high-pressure die casting, a high shear melt conditioning (HSMC) technology was developed and applied to the melt prior to pouring into the shot sleeve. The experimental results show that, with the application of HSMC, the variation of elongation and yield strength was decreased from 21.8% and 5.5% to 13.9% and 3.6%, respectively. The improved mechanical performance is attributed to the enhanced heterogeneous nucleation in both the shot sleeve and the die-cavity of the die-caster, and also to the improved distribution of the secondary phases and reduced casting defects, including porosity, as a benefit of grain refinement induced by high shear. With the application of high shear, large numbers of the spinel phase (MgAl2O4) particles with double size distribution and average diameter of 80 nm and 300 nm were formed. Due to the good orientation relationship and small misfit between (α)-Al and MgAl2O4, the particles act as effective nuclei in the shot sleeve and the die cavity, respectively.

23 September 2022 in Metals
Verified
Journal Article
Open access
PDF file
ELEwan Lordan
Ewan Lordan
Yijie ZhangYijie Zhang
Yijie Zhang
KUN DOUKUN DOU
KUN DOU
AJAlain JACOT
Alain JACOT
CTChrysoula Tzileroglou
Chrysoula Tzileroglou
Zhongyun FanZhongyun Fan
Zhongyun Fan
This article provides an overview of high-pressure die casting (HPDC)-related research undertaken at the EPSRC Future LiME Hub between 2015–2022. The project aimed to identify the cause of variability in the tensile ductility of die-cast structures, and to develop novel processing techniques to address this issue. Variability in tensile ductility was related to the size of large pores and non-metallic inclusions. It was proposed that these non-metallic inclusions formed during the pyrolysis of commercial plunger lubricants in the shot sleeve, and that these large pores derived from dilatational strains introduced during semi-solid deformation. Processing parameters and die design were found to significantly influence the microstructure of die-cast products, and the subsequent variability in tensile ductility. To close, recent progress on the application of intensive melt shearing to HPDC is reviewed. Intensive melt shearing was found to induce significant grain refinement in both Al and Mg alloys due to the effective dispersion of native oxide particles, and the use of these particles as heterogeneous nucleation substrates. The presence of native oxide particles also enabled the use of novel heat treatment procedures that avoided conventional issues such as surface blistering and geometrical distortion.

1 May 2019 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
Jaime Lazaro NebredaJaime Lazaro Nebreda
Jaime Lazaro Nebreda
JPJ B Patel
J B Patel
ICI T H Chang
I T H Chang
ISI C Stone
I C Stone
Zhongyun FanZhongyun Fan
Zhongyun Fan
The accumulation of iron in molten aluminium is one of the main concerns for the recycling and casting industries because it leads to the formation of undesirable Fe-rich intermetallic compounds which are detrimental to mechanical properties. Many methods have been developed in the past to reduce the iron accumulated in molten aluminium scrap, but they all suffer from poor efficiency. Hence, a more efficient method is urgently needed to mitigate the negative effect of high iron levels in the melt, thereby avoiding downgrading secondary aluminium to low quality products or the dilution with expensive primary aluminium. This contribution provides a study of the Fe-rich intermetallic compounds developed in aluminium casting alloys with high levels of Fe as a function of melt processing conditions. Results show that the formation of the Fe-compounds is not only dependent on the cooling rate and holding time before solidification, but more on the initial melt treatment as it enhances the nucleation and growth of the Fe-phases. Elemental addition of Mn leads to the formation of large and compact intermetallic particles, but at slow rate. Physical melt treatment by intensive high shearing produces a much faster nucleation and results in a fine dispersion of smaller iron containing intermetallic particles. The latter could be used either to increase the tolerance to iron contamination or to facilitate the iron removal process, providing huge benefits for the recyclability of scrap aluminium alloys as it would allow the transformation of low-grade feedstock into a low cost and small carbon footprint material for high quality castings.