Poly(methylvinylsiloxane) (V₃ polymer) obtained by kinetically controlled anionic ring-opening polymerization of 1,3,5-trimethyl-1,3,5-trivinylcyclotrisiloxane was cross-linked with various amounts of 1,3,5,7-tetramethylcyclotetrasiloxane (D₄^H) in w/o high internal phase emulsions (HIPEs). PolyHIPEs thus prepared differed in the polymer cross-linking degree, which affected their porous morphology and total porosity. The obtained V₃ polymer-based polyHIPEs were applied as matrices for the incorporation of Pd from the Pd(OAc)₂ solution in tetrahydrofuran. This process involved the conversion of Si–H groups remaining in the polymer networks and resulted in the formation of crystalline, metallic Pd in the systems. Mean sizes of the generated Pd crystallites were lower in polyHIPEs of higher than in those of lower polymer cross-linking degrees and porosities (∼5 nm vs ∼8 nm, respectively). The Pd-containing polyHIPEs showed activity in catalytic hydrogenation of the triple carbon–carbon bond in phenylacetylene giving the unsaturated product, styrene with a selectivity of ca. 80%. To the best of our knowledge, this is the first work devoted to polysiloxane-based polyHIPEs with dispersed metallic particles.

Polysiloxane networks were prepared by hydrosilylation of poly(methylvinylsiloxane) (V₃ polymer) with 1,3,5,7-tetramethylcyclotetrasiloxane (D₄^H) at various Si-Vinyl: Si-H groups molar ratios in water-in-oil high internal phase emulsion (HIPE). Curing the emulsions followed by removal of water led to foamed cross-linked polysiloxane systems differing in the cross-linking degrees, as well as residual Si-H and Si-Vinyl group concentrations. Treatment of thus obtained materials in Pd(OAc)₂ solution in tetrahydrofuran resulted in the formation of porous palladium/polymer nanocomposites with different Pd contents (1.09–1.70 wt %). Conducted investigations showed that pyrolysis of the studied materials at 1000 °C in argon atmosphere leads to porous Si-C-O and Si-C-O/Pd ceramics containing amorphous carbon and graphitic phases. Thermogravimetric (TG) analysis of the starting cross-linked polymer materials and those containing Pd nanoparticles revealed that the presence of palladium deteriorates thermal stability and decreases ceramic yields of preceramic networks. The extent of this effect depends on polymer cross-linking density in the system.

Poly(hydromethylsiloxane) (PHMS) was cross-linked with 1,3,5,7-tetramethyl-1,3,5,7-tetravinylcyclotetrasiloxane (D₄^Vi) in water-in-oil High Internal Phase Emulsions to form macroporous materials known as polyHIPEs. It was shown that in the process of pyrolysis under Ar atmosphere at 520 °C, the obtained polyHIPEs were converted to ceramers with high yields (82.8–88.0 wt.%). Structurally, the obtained ceramers were hybrid ceramics, i.e., they consisted of Si-O framework and preserved organic moieties. Macropores present in the polyHIPE precursors remained in ceramers. Ceramers contained also micro- and mesopores which resulted from the precursor’s mass loss during pyrolysis. Total pore volume and BET specific surface area related to the existence of micro- and mesopores in ceramers depended on the PHMS: D₄^Vi ratio applied in polyHIPE synthesis. The highest total pore volume (0.143 cm³/g) and specific surface area (344 m²/g) were reached after pyrolysis of the precursor prepared with the lowest amount of D₄^Vi as compared to PHMS. The composite materials obtained after deposition of PdO nanoparticles onto ceramers followed by reduction of PdO by H₂ were active and selective catalysts for phenylacetylene hydrogenation to styrene.