Spatio-temporal ground-movement measurements and mappings have been carried out in the Campine coalfield in Belgian Limburg since the closure of the mines to document post-mining effects. MT-InSAR measurements are compared to groundwater head changes in the overburden and to height data from the closest GNSS stations. Radar interferometry is used to estimate the extension and the velocity of ground movements. In particular, the MT-InSAR technique has been applied to SAR acquisitions of the satellites ERS-1/2 (1991–2005), ENVISAT (2003–2010), COSMO-SkyMed (2011–2014), and Sentinel-1A (2014–2022). The images were processed and used to highlight a switch from subsidence to uplift conditions in the western part of the coal basin, while the eastern part had already been affected by a rebound since the beginning of the ERS-1/2 acquisitions. Following the closure of the last active colliery of Zolder in 1992 and the subsequent cease of mine-water pumping, a recharge of mine-water aquifers occurred in the western part of the basin. This process provoked the change from subsidence to uplift conditions that was recorded during the ENVISAT period. In the center of the coal-mining area, measured uplift velocities reached a maximum of 18 mm/year during the ENVISAT period, while they subsided at −12 mm/year during the ERS-1/2 period. Mean velocities in the western and eastern parts of the coalfield area have decreased since the last MT-InSAR measurements were performed using Sentinel-1A, while the Zolder coal mine continues to rise at a faster-than-average rate of a maximum of 16 mm/year. The eastern part of the coalfield is still uplifting, while its rate has been reduced from 18 mm/year (ERS-1/2) to 9 mm/year (Sentinel-1A) since the beginning of the radar–satellite observations. Time-series data from the two GNSS stations present in the study area were used for a local comparison with the evolution of ground movements observed by MT-InSAR. Two leveling campaigns (2000, 2013) were also used to make comparisons with the MT-InSAR data. The station’s measurements and the leveling data were in line with the MT-InSAR data. Overall, major ground movements are obviously limited to an extension of the actual underground-mining works and rapidly diminish outside of them.
Worldwide, flood events frequently have a dramatic impact on urban societies. Time is key during a flood event in order to evacuate vulnerable people at risk, minimize the socio-economic, ecologic and cultural impact of the event and restore a society from this hazard as quickly as possible. Therefore, detecting a flood in near real-time and assessing the risks relating to these flood events on the fly is of great importance. Therefore, there is a need to search for the optimal way to collect data in order to detect floods in real time. Internet of Things (IoT) is the ideal method to bring together data of sensing equipment or identifying tools with networking and processing capabilities, allow them to communicate with one another and with other devices and services over the Internet to accomplish the detection of floods in near real-time. The main objective of this paper is to report on the current state of research on the IoT in the domain of flood detection. Current trends in IoT are identified, and academic literature is examined. The integration of IoT would greatly enhance disaster management and, therefore, will be of greater importance into the future.
Surface moisture plays a key role in limiting the aeolian transport on sandy beaches. However, the existing measurement techniques cannot adequately characterize the spatial and temporal distribution of the beach surface moisture. In this study, a mobile terrestrial LiDAR (MTL) is demonstrated as a promising method to detect the beach surface moisture using a phase-based Z&F/Leica HDS6100 laser scanner mounted on an all-terrain vehicle. Firstly, two sets of indoor calibration experiments were conducted so as to comprehensively investigate the effect of distance, incidence angle and sand moisture contents on the backscattered intensity by means of sand samples with an average grain diameter of 0.12 mm. A moisture estimation model was developed which eliminated the effects of the incidence angle and distance (it only relates to the target surface reflectance). The experimental results reveal both the distance and incidence angle influencing the backscattered intensity of the sand samples. The standard error of the moisture model amounts to 2.0% moisture, which is considerably lower than the results of the photographic method. Moreover, a field measurement was conducted using the MTL system on a sandy beach in Belgium. The accuracy and robustness of the beach surface moisture derived from the MTL data was evaluated. The results show that the MTL is a highly suitable technique to accurately and robustly measure the surface moisture variations on a sandy beach with an ultra-high spatial resolution (centimeter-level) in a short time span (12 × 200 m per minute).
The digital age has brought about an explosion in the growth of data, of which data with a geographical component stands out. Proper use of geographical data comes with the need for correct coordinate reference systems (CRSs). They are considered the ultimate binder for interoperability between geospatial data actors and stakeholders. Moreover, CRSs are crucial for the visual and analytical integration of geospatial data from disparate data sources. However, CRSs might be—for numerous reasons—incorrectly assigned or even missing. The result is a time-consuming study of the map, literature, and available resources to ultimately find the alleged right CRS. This study provides a summary of prevailing resources from national mapping agencies of some European countries to address the above problem. Secondly, and most importantly, is the development of an open-source Python-based software package. This software package aims to accurately estimate the best candidate CRS, given a tuple of coordinates at a priori an approximately known location. It is controlled by geocoding the known location and intersecting the resulting coordinate with the bounding box of all CRSs in the EPSG-database. An in-depth review of CRS tools by mapping authorities reveals, in particular, limitations concerning the countries’ spatial areas, in combination with often required know-how of local CRSs. To address these shortcomings, our tool is developed to enable a more generic extraction of CRSs for any given location worldwide. Testing proved successful for 30 different maps, with a grid present on the map and the CRS of the map being included in the EPSG-database.
The North Sea is a shallow sea that forms a complex physical system. The nonlinear interaction of the astronomical tides, varying wind fields and varying pressure systems requires appropriate approaches to be described accurately. An application based on the advanced numerical model Regional Ocean Modeling System (ROMS) was newly developed by the authors, tailored to simulate these hydrodynamic processes in the North Sea and the Belgian Continental Shelf, which is the area of particular interest in the present study. The purpose of this work is to develop and validate a state-of-the-art three-dimensional numerical model to form the basis of a compound operational and forecasting tool for the Belgian coastal zone. The model was validated with respect to water levels and temperature. Validation for astronomical tides was accomplished through the comparison of the principal constituents between the model results and observations at a number of tidal gauges in Belgium and other countries. A statistical analysis of the results showed that the model behaves as expected throughout the North Sea. The model response to the varying meteorological conditions was also validated using hindcast data for 2011 as input. In this case, the comparison between observed and modelled water levels showed a good agreement with average RMSE in Belgium 9.5 cm. Overall, the added value of this work is the development of an independent model for validation and comparison with other models and which can be used as an efficient tool for operational and forecasting purposes.
The archive of aerial photographs, dating 1935–1941 and covering parts of north and central of Ethiopia, is one of the few archives with pre‐1960 remotely sensed data in Africa. It allows adding 30 years of time depth for geographical studies, in contrast to the commonly known oldest imagery dating to 1964, sometimes 1958. These photographs were originally acquired by the Italian military forces, to obtain raw material for warfare purposes and the production of topographic maps. To make the archive accessible, it has been scanned and georeferenced. Procedures used in georeferencing and digitally archiving are detailed in this paper, as well as our experiences with orthorectification and use of the photosets in scientific research. This data set of aerial photographs of Ethiopia in the 1930s has been availed to the wider scientific community through the Pangaea website http://doi.org/10.1594/PANGAEA.920077 (Nyssen et al., 2020, Aerial photographs of Ethiopia 1935–1941) Additionally, a web interface (http://www.ethiopia1935.ugent.be/) allows scientists visualizing the location of relocated photographs, and to select and freely order scenes of interest.