Photonic Integrated Circuits (PICs) are taking a major role in the telecommunications and datacenter markets. The increased complexity of coexisting and fast evolving standards for Passive Optical Networks (PONs) suggests the introduction of PICs will be the next step in PON related optoelectronics. The PICs ecosystem has greatly matured in the past years, becoming a solution that can cope with the requirements of industry and academia, and presenting the flexibility of combining multiple platforms available towards viable commercial solutions. In this review, the evolution of PONs and PICs is presented, with a focus on the optoelectronic integration of PICs for PONs and coherent PONs. To demonstrate the potential of PICs and their combination with electronics, a quasi-coherent receiver based on co-hosted PIC and Application Specific Integrated Circuit (ASIC) is presented and characterized.
A potentially cost-effective approach for augmenting the transmission capacity in an optical transport network (OTN) consists of bundling several optical channels by means of an inverse-multiplexing strategy, e.g. virtual concatenation (VCAT). When VCAT is employed together with multipath routing, the differential delay between concatenated channels needs to be compensated via electrical buffering. To avoid installing large and costly high-speed buffers, this compensation can be dispersed throughout the intermediate path nodes. With this distributed scheme, each intermediate compensation operation requires an optical-electrical-optical (OEO) converter. Such converters, which are typically employed to allow electrical processing (e.g. signal regeneration, traffic switching/grooming, etc.), represent the largest contributor to the capital expenditures of an optical network. Hence, to save on OEO equipment and keep the network cost-effectiveness, we propose the novel approach of collocating the differential delay buffering and the regeneration on the same network element, enabling the implementation of distributed schemes with minimal link capacity levels, OEO count, and buffer size requirements. To effectively design an OTN network under these conditions, we also present a new multi-step optimization framework based on integer linear programming (ILP) modeling. To test our approach, emerging 100 Gb/s Ethernet services are established over two reference networks using virtually-concatenated 40 Gb/s channels. The correspondent results confirm that relevant OEO/regenerator count savings (ranging from 23% to 44%) can be attained with the collocated approach while the buffer sizes are maintained reasonably small. We also show that the end-to-end transmission latency is not affected by the adoption of this collocated strategy
A hybrid integration of a PIC and an ASIC for achieving quasi-coherent receiver designed for tunable 10 Gbit/s applications is presented. This assembly holds the key functionalities for enabling integrated, highly efficient, tunable transceivers which can also enable TWDM-PON.
14 October 2021 in IEEE Photonics Technology Letters
This letter reports a novel approach for nonlinear phase noise mitigation, based on artificial neural networks (ANNs) tailored to classification applications and a pre-processing stage of feature engineering. Starting with a set of proof-of-concept simulations, we verify that the proposed system can achieve optimal performance for the additive white Gaussian noise (AWGN) channel. Then, considering a dispersion-less channel with strong nonlinear phase noise (NLPN) distortion, we demonstrate a Q-factor increase of 0.4dB, comparing with standard carrier-phase estimation (CPE) followed by minimum distance detection. Finally, simulating the propagation of 64Gbaud PM-16QAM over standard single mode fiber (SSMF), we verify that the ANN-based solution is effective on wavelength-division multiplexing (WDM) transmission conditions, enabling to increase the maximum signal reach by approximately 1 fiber span over the legacy CPE-enabled NLPN compensation.
The increasing traffic demand resulting from the widespread use of information and communication technologies is impelling network operators to upgrade the capacity of their existing transport network facilities. Recent advances in the scientific community have led to the first developments in serial 100 Gb/s technology that could provide an adequate solution for solving the capacity expansion problem. Nevertheless, given the complexity of 100 Gb/s transceiver equipment, the initial costs may refrain early adoption of the technology, leading carriers to invest in more cost-effective alternatives. Embedded in the optical transport network (OTN) functionality portfolio, traffic grooming and virtual concatenation can be exploited in order to optimally combine 40 Gb/s and 100 Gb/s equipment for supporting mixed line rate (MLR) demands. Hence, this work proposes an optimization framework for designing optical transport infrastructures with the objective of minimizing the network costs directly related to transceiver and regenerator equipment. The framework models the problem via an integer linear programming formulation that takes into account the relative cost, the maximum optical reach, and the capacity of each optical interface, as well as the optical channel limit per fiber link. As a result, the proposed method is able to select the equipment type and the routing path for each connection which correspond to the most cost-effective solution satisfying the 100G and 40G service demands.
Lithography variation presents one of the biggest challenges for photonic component optimization, especially for fabless designers. Lithography prediction models are a crucial tool for minimizing the necessary number of fabrication iterations for a device’s optimization. This paper presents one of these models specifically adapted for the contra-directional coupler structure. Through the experimental characterization of devices with a specific range of design parameters, it was possible to observe how the lithography process impacts their performance. A correction model based on effective refractive index variation and its impact on the Bragg condition of the structure was developed to predict the performance variation of a device based on the expected design variation induced by fabrication. The contra-directional couplers fabricated at CORNERSTONE foundry show a tendency to be redshifted as the gap decreases, due to an increase in waveguide width as a result of a diffraction-limited lithography process. Based on these and other findings, it was possible to correlate the design parameters to the posterior fabricated structure and ultimately predict the expected experimental response.