Juan Pablo Morales

Dr. Juan Pablo Morales

Universidad ECCI, Bogotá, Colombia

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 September 2022 in Polymers
Verified
Journal Article
Open access
PDF file
Eliana M. AgaliotisEliana M. Agaliotis
Eliana M. Agaliotis
BABaltazar D. Ake-Concha
Baltazar D. Ake-Concha
APAlejandro May Pat
Alejandro May Pat
Juan Pablo MoralesJuan Pablo Morales
Juan Pablo Morales
Celina Raquel BernalCelina Raquel Bernal
Celina Raquel Bernal
EFEmmanuel A. Flores-Johnson
Emmanuel A. Flores-Johnson
Natural fiber-reinforced composite (NFRC) filaments for 3D printing were fabricated using polylactic acid (PLA) reinforced with 1–5 wt% henequen flour comprising particles with sizes between 90–250 μm. The flour was obtained from natural henequen fibers. NFRCs and pristine PLA specimens were printed with a 0° raster angle for tension tests. The results showed that the NFRCs’ measured density, porosity, and degree of crystallinity increased with flour content. The tensile tests showed that the NFRC Young’s modulus was lower than that of the printed pristine PLA. For 1 wt% flour content, the NFRCs’ maximum stress and strain to failure were higher than those of the printed PLA, which was attributed to the henequen fibers acting as reinforcement and delaying crack growth. However, for 2 wt% and higher flour contents, the NFRCs’ maximum stress was lower than that of the printed PLA. Microscopic characterization after testing showed an increase in voids and defects, with the increase in flour content attributed to particle agglomeration. For 1 wt% flour content, the NFRCs were also printed with raster angles of ±45° and 90° for comparison; the highest tensile properties were obtained with a 0° raster angle. Finally, adding 3 wt% content of maleic anhydride to the NFRC with 1 wt% flour content slightly increased the maximum stress. The results presented herein warrant further research to fully understand the mechanical properties of printed NFRCs made of PLA reinforced with natural henequen fibers.

8 February 2012 in Journal of Composite Materials
Verified
Journal Article
Closed access
PDF file
Juan Pablo MoralesJuan Pablo Morales
Juan Pablo Morales
AVAnalía Vazquez
Analía Vazquez
MEMariano M Escobar
Mariano M Escobar
Glass fiber-reinforced polymer bars are currently used to reinforce concrete in an attempt to overcome the corrosion issue encountered with ordinary steel. Different types of surface treatment were applied to the smooth rods in order to enhance bonding with concrete. Experimental results show that using bars coated with coarse sand notably improve the bond strength. The influence of granulometry sand, rebar diameter, length embedded, and concrete strength are analyzed. Rebars coated with finer sand lead to a stronger chemical adhesion with concrete. However, the effect of friction and interlocking forces produced by coarse sand prevails over the chemical adhesion in the pull-out test.

2 March 2016 in Advances in Polymer Technology
Verified
Journal Article
Closed access
Juan Pablo MoralesJuan Pablo Morales
Juan Pablo Morales
CBCelina Bernal
Celina Bernal
AVAnalía Vázquez
Analía Vázquez
MEMariano M. Escobar
Mariano M. Escobar

7 September 2021 in Journal of Natural Fibers
Verified
Journal Article
Closed access
Eliana M. AgaliotisEliana M. Agaliotis
Eliana M. Agaliotis
Juan Pablo MoralesJuan Pablo Morales
Juan Pablo Morales
Celina Raquel BernalCelina Raquel Bernal
Celina Raquel Bernal
Novel intralayer hybrid composites (IHC) based on a commercial polylactic acid (PLA) matrix reinforced with a hybrid plain-woven fabric, composed of PLA filaments and sisal fibers, were obtained by film stacking followed by compression molding. Two different stacking configurations were explored. In one configuration, weft and warp directions of all fabric layers were equally oriented whereas in the other configuration, weft and warp directions of fabric layers were alternately oriented. The effect of the stacking sequence on the materials morphology and thermal and tensile behavior was investigated. All obtained composites presented higher thermal stability than the matrix due to the presence of the natural fibers and PLA filaments and also, the existence of lignocellulosic compounds in the woven fabric led to a char yield residue, with the expected improvement of flame retardant properties. Although both IHCs exhibited highly anisotropic tensile behavior, the composite having an alternated fabric layers configuration, presented a good balance of stiffness and strength for the two main orthogonal loading directions.

24 February 2016 in Polymers for Advanced Technologies
Verified
Journal Article
Closed access
PDF file
MLM. C. Lucchetta
M. C. Lucchetta
Juan Pablo MoralesJuan Pablo Morales
Juan Pablo Morales
MMM. Mollo
M. Mollo
Celina Raquel BernalCelina Raquel Bernal
Celina Raquel Bernal

9 July 2013 in Journal of Composite Materials
Verified
Journal Article
Open access
PDF file
Juan Pablo MoralesJuan Pablo Morales
Juan Pablo Morales
MEMariano Escobar
Mariano Escobar
AVAnalia Vazquez
Analia Vazquez
The viscoelastic properties of nanocomposites based on epoxy and epoxy-phenolic blend matrix reinforced with multi-wall carbon nanotubes were studied. The content of carbon nanotube (0.2 and 0.5 wt.%) and its surface state (pristine vs. oxidized) varied. The characterization of the nanocomposites was done by means of infrared spectroscopy and chemical methods. From the viscoelastic properties of nanocomposites, characteristic properties such as storage modulus ( E0), tan δ and damping peak (tan δ) were obtained. The void content was also determined. Also, Weibull statistics are used to represent the failure of secondary bonds during the relaxation processes that lead to stiffness change over the full range of use temperatures. The incorporation of phenolic resin to an epoxy matrix leads to an increase of the relaxation modulus. The glass transition temperature of the epoxy-phenolic nanocomposites decrease when it is incorporated carbon nanotubes, independently of its state (pristine or oxidized).