Uncoated weathering steel (UWS) bridges have been extensively used to reduce the lifecycle cost since they are maintenance-free and eco-friendly. However, the fatigue issue becomes significant in UWS bridges due to the intended corrosion process utilized to form the corrodent-proof rust layer instead of the coating process. In this paper, an innovative model is proposed to simulate the corrosion-fatigue (C-F) process in UWS bridges. Generally, the C-F process could be considered as two relatively independent stages in a time series, including the pitting process of flaw-initiation and the fatigue crack propagation of the critical pitting flaw. In the proposed C-F model, Faraday’s law has been employed at the critical flaw-initiation stage to describe the pitting process, in which the pitting current is applied to reflect the pitting rate in different corrosive environments. At the crack propagation stage, the influence of pitting corrosion is so small that it can be safely ignored. In simulating the crack propagation stage, the advanced NASGRO equation proposed by the NASA is employed instead of the classic Paris’ law, in which a modified fatigue limit is adopted. The fatigue limit is then used to determine the critical size of pitting flaws, above which the fatigue effect joins as a parallel driving force in crack propagation. The model is then validated through the experimental data from published articles at the initiation stage as well as the whole C-F process. Two types of structural steel, i.e., HPS 70W and 14MnNbq steel, have been selected to carry out a case study. The result shows that the C-F life can be notably prolonged in the HPS 70W due to the enhancement in fatigue strength and corrosion resistance. Besides, a sensitivity analysis has been made on the crucial parameters, including the stress range, stress ratio, corrosive environment and average daily truck traffic (ADTT). The result has revealed the different influence of the above parameters on the initiation life and propagation life.

Floating modular energy islands (FMEIs) are modular, interconnected floating structures designed to collectively produce, store, convert, and transport renewable energy. This review aims to establish a foundation for developing innovative approaches to sustainably harness multi-energy sources in offshore environments. It leverages existing technological expertise while exploring new solutions to address specific challenges associated with FMEIs. The review initially presents existing technologies for floating energy structures and assesses their applicability to FMEI. The structural materials that could be utilised for the construction of a floating energy island are subsequently reviewed. Next, the offshore construction technologies suitable for FMEI are reviewed. Finally, studies on the life cycle assessment of hybrid energy systems are examined, highlighting the environmental advantages of integrating multiple renewable energy sources, thereby underscoring the potential of FMEIs.

As a critical component of a suspension bridge, the integrity of the suspenders plays a critical role in the serviceability and reliability of the bridge during its life time. Despite the wide recognition of the importance of the suspenders, very few studies have been devoted to the condition evaluation of suspenders in operation. The present study performs the fatigue assessment on the suspenders accounting for the stochastic wind and traffic loads using the in-situ monitoring data. To this end, a probabilistic numerical framework is proposed to predict the time-dependent fatigue reliability of the suspenders under stochastic wind and traffic loads during the bridge’s life time, based on the linear fatigue damage rule. As a demonstration, the proposed numerical framework is applied to a long-span suspension bridge located in a mountainous canyon. The results indicate that it is of paramount importance to consider both the wind and traffic load effects in the fatigue reliability evaluation of the suspenders. In addition, it was also found that among the suspenders under investigation, the short suspender at the bridge mid-span (S36) is more prone to the fatigue damage, while the long suspender at the end of the bridge girder (S2) is less prone to the fatigue damage. Finally, provided with a target reliability index of 3.0, the fatigue life of the suspenders S36 and S2, considering the life time wind and traffic load, is estimated as 53 years and 167 years, respectively. The present research could provide essential guidelines for the optimization of inspection and replacement in maintenance practices for suspenders.

Rib-to-deck (RD) joints in orthotropic steel decks (OSDs) are highly prone to fatigue cracking under heavy traffic. An innovative longitudinal rib, named the thickened edge U-rib (TEU), has been proposed to enhance the fatigue strength of RD joints and validated through model tests. However, more studies are still required on the effect of TEUs in real engineering applications. To this end, a typical OSD bridge in China has been investigated, based on the experimental results. In the analysis, a stochastic traffic model is employed to simulate the vehicle-induced fatigue actions comprehensively. The framework of the stochastic model is proposed by considering the randomness in both the vehicles and their lateral distribution. Then the traffic model is instantiated using standard truck models in conjunction with the codes of practice as well as the observed data. A multi-scale finite element model is later established to determine the stochastic stress responses, whereas the influence surface method is used to improve computational efficiency. In this study, Monte Carlo simulations have been carried out to derive the stress spectra for the RD joints at different critical locations. Based on the test data and the derived spectra, an engineering assessment has been performed to obtain the fatigue life of RD joints in OSDs with and without TEUs, respectively. The new findings show that the position of joints has a remarkable influence on the stress spectra of RD joints, which results in the notable difference in fatigue life of the joints. Further, the fatigue life of RD joints can be significantly prolonged by using TEUs, and the prolongation rates are varied from 141% to 161% depending on the calculation methods and traffic models used.