The microfluidic chip can be used to separate particles via the acoustic radiation force and can be applied to the separation of impurity particles from lubricating oil. A device that separates particles by controlling the acoustic radiation force via standing surface acoustic waves (SSAWs) was proposed. The concentration and separation of suspended particles were simulated by using the COMSOL Multiphysics modeling software. The force exerted on suspended particles and their subsequent motion in the microfluidic channel were analyzed, and then the concentration of particles exposed to SSAWs was verified. We also investigate how the frequency of the SSAW affects the particle concentration and discuss the advantage of using SSAWs to concentrate and separate particles. The separating feasibility was verified by suspended particles in lubricating oil experiments according to simulation results.
This paper reports numerical studies of an Elasto-Hydrodynamic (EHD) seal, which is being developed for supercritical CO2 (sCO2) turbomachinery applications. Current sCO2 turbomachinery suffers from high leakage rates, which is creating a major roadblock to the full realization of sCO2 power technology. The high leakage rates not only penalize the efficiencies but also create environmental concerns due to greenhouse effects caused by the increased CO2 discharge to the atmosphere. The proposed EHD seal needs to work at elevated pressures (10–35 MPa) and temperatures (350–700 °C) with low leakage and minimal wear. The unique mechanism of the EHD seal provides a self-regulated constriction effect to restrict the flow without substantial material contact, thereby minimizing leakage and wear. This work utilizes a physics-based modeling approach. The flow through the gradually narrowing seal clearance is modeled by the well-known Reynolds equation in EHD lubrication theory, while the deformation of the seal is modeled by using the governing equations of three-dimensional solid mechanics. As for the solution methodology, COMSOL’s Thin-Film Flow and Solid Mechanics modules were employed with their powerful capabilities. The numerical results were presented and discussed. It was observed that the Reynolds equation fully coupled with the surface deformation was able to successfully capture the constriction effect. The maximum and minimum leakages were calculated to be 2.25 g/s and 0.1 g/s at P = 5.5 MPa and P = 11 MPa for the design seal, respectively. It was interesting to observe that the seal leakage followed a quadratic trend with increasing pressure differential, which can become advantageous for high-pressure applications such as sCO2 power generation technology.
30 September 2025 in ASCE-ASME Journal of Risk and Uncertainty in Engineering Systems, Part B. Mechanical Engineering
The remaining useful life (RUL) estimation is an important metric that helps in condition-based maintenance. Damage data obtained from the diagnostics techniques are often noisy, and the RUL estimated from the data is less reliable. Estimating the probabilistic RUL by quantifying the uncertainty in the predictive model parameters using the noisy data increases confidence in the predicted values. In this work, Bayesian inference is used to inversely quantify the uncertainty in the model parameters of the predictive damage model in adhesively bonded joints, and quantified parameter uncertainty is represented by a probability distribution function (PDF). It is difficult to obtain a closed-form solution for the RUL from the PDF of model parameters due to the nonlinearity of the damage models. Instead, statistical simulations are used to generate the model parameter samples from the PDF, and the RUL is estimated from the samples. In the statistical simulations, the predictive damage model is evaluated for each parameter sample. Using a physics-based model as the predictive model increases computational time, which makes the statistical techniques to be computationally expensive. It is essential to reduce the computational time to estimate the RUL in a feasible time. In this work, real-time probabilistic RUL estimation is demonstrated in adhesively bonded joints using the Sequential Monte Carlo (SMC) sampling method and cloud-based computations. The SMC sampling method is an alternative to traditional Markov Chain Monte Carlo (MCMC) methods, which enables generating statistical parameter samples in parallel. The parallel computational capabilities of the SMC methods are exploited by running the SMC simulation on multiple cloud calls. This approach is demonstrated by estimating fatigue RUL in the adhesively bonded joint. The accuracy of probabilistic RUL estimated by SMC is validated by comparing it with RUL estimated by the MCMC and the experimental values. The SMC simulation is run on the cloud and the computational speedup of the SMC is demonstrated.
11 November 2026 in ASCE-ASME Journal of Risk and Uncertainty in Engineering Systems, Part B. Mechanical Engineering
Thermal protection systems (TPS) of space vehicles are designed computationally rather than experimentally. They are validated using ground experiments, but all aspects of the flight cannot be replicated on ground. This ground-to-flight mapping introduces uncertainties that need to be accounted for while designing any thermal protection system. Thus, precise computational models along with uncertainty quantification in the models are required to design the TPS. The focus of this study is to estimate the thermal material parameters of TPS based on the target reliability requirements using statistical methods. To perform uncertainty quantification (UQ) of a system, a simulated model of the system needs to be solved many times on statistical samples, increasing the computational time and cost. In this study, a physics-informed neural network (PINN) model is used instead of traditional physics-based numerical solutions. The accuracy of PINN is comparable to that of the numerical solution. To find the parameter distribution, sampling of the parameter space is performed using sequential Monte Carlo (SMC) method. Combining the use of both PINN predictive model and SMC sampling, the framework can approximate the parameter distributions that satisfy the TPS design reliability constraints. The framework achieved a remarkable increase in the speed of performing the reliability analysis; specifically, the time required to process 10,000 samples was reduced 175 times using the proposed PINN-SMC approach. This reliability analysis can be used for design optimization of the TPS based on risk analysis along with other systems of vehicle.