Discharging livestock manure slurry without proper treatment causes various environmental and sociological problems. Chemical coagulation is a widely used and easily applicable method for treating such wastewater. However, the technique requires optimization to enhance coagulation efficiency while minimizing chemical usage. In this study, we propose an efficient, low-cost, and environmentally safe chemical coagulation method for solid–liquid separation of dairy manure slurry. Experiments were conducted in laboratory jar tests using dairy manure slurry to investigate the impact of coagulants, specifically polyaluminum chloride (PAC) and cationic polyacrylamide (CPAM), as well as pH, on the process of solid-liquid separation. Preliminary ranges of PAC, CPAM, and pH were estimated through single-factor experiments. Coagulation optimization and modeling were performed using the response surface methodology (RSM) with the Box-Behnken design (BBD), wherein the desired goal of each parameter was set to maximize solid–liquid separation efficiency while reducing chemical dosage to maintain residual aluminum (Al) concentrations below water quality standards. Numerical optimization predicted that the optimal dosages were 75 mg/L of PAC and 35 mg/L of CPAM at pH 7. Under these conditions, removal efficiencies of 99% for turbidity and 97% for chemical oxygen demand (COD) were achieved, with a minimal residual Al concentration of 0.045 mg/L. Positive zeta potential values in the treated water confirmed complete separation of negatively charged solids in the dairy manure slurry. The response values predicted by BBD aligned with the experimental results, and the analysis of variance (ANOVA) demonstrated the predictability and accuracy of the response models. Consequently, this study highlights the practical application of RSM with BBD in optimizing chemical coagulation using PAC and CPAM to achieve efficient solid–liquid separation in livestock wastewater while maintaining low residual Al concentrations.

Cyanobacterial blooms are a threat to the drinking water supply owing to their potential toxicity. Microcystins which are the most widespread cyanotoxins, are mainly produced by Microcystis spp. In this study, we cultured Microcystis aeruginosa cells in BG-11 medium at 25 °C to investigate the efficiency of the electro-coagulation–flotation process to remove them. Different anode materials (Fe, Al, Cu, and Zn) along with a graphite cathode were compared separately in the 10–100 mA current range in a 0.025 M Na₂SO₄ electrolyte. Turbidity, optical density at 684 nm (OD₆₈₄), OD₇₃₀, Chl-a concentration, and DOC concentration were analyzed to clarify the mechanism by which M. aeruginosa cells are removed. The Al anode indicated the highest removal efficiencies in terms of turbidity (90%), OD₆₈₄ and OD₇₃₀ (98%), and Chl-a concentration (96%) within 30 min at 4.0 mA/cm² current density and the lowest average electrode consumption of 0.120 ± 0.023 g/L. The energy consumption of the Al electrode was 0.80 Wh/L. From these results, we found that Al was the best among the anode materials evaluated to remove M. aeruginosa cells. However, further studies are required to optimize the Al anode in terms of pH, treatment time, electrode distance, and electrolyte concentration to enhance the removal of M. aeruginosa cells.

Palm oil mill effluent (POME) is considered the most environmentally harmful when discharged without proper treatment. In addition to conventional biological treatment methods, physicochemical treatment techniques are considered alternative methods to treat POME as polishing or post-treatment techniques to meet the discharge water quality standards set by authorities. Recently, electroflotation (EF) has gained popularity in wastewater treatment owing to its high efficiency, no harmful by-products, and ease of operation. However, EF has limitations on energy consumption because high current density and long electrolysis time are often used to increase the density of gas bubbles and metallic ions produced in the EF system used in pollutant removal. Polyaluminum chloride (PAC) and cationic polyacrylamide (CPAM) are used as alternative options for the production of coagulants instead of using a sacrificial anode in EF. In this study, we hypothesized that PAC and CPAM could enhance the efficiency and reduce the specific energy consumption of EF by minimizing the electrolysis time used in POME treatment. The effects of electrolysis time, current density, and coagulant dosage on POME treatment were investigated. EF treatment at a current density of 2.5 mA/cm² has achieved 82% of turbidity and 47% of chemical oxygen demand (COD) removal after 45 min electrolysis time, consuming 0.014 kWh of specific energy for the treatment of one gram of COD. There was no improvement in terms of turbidity removal when the current density was increased from 2.5 to 5 mA/cm²; however, the COD removal efficiency was increased up to 52% at 5 mA/cm². When EF was performed at 1 A combined with PAC at a dosage of 40 mg/L and CPAM at a dosage of 20 mg/L, it was noticed that turbidity and COD removal increased up to 96% and 54%, respectively, within 15 min electrolysis. Subsequently, the specific energy consumption was reduced to 0.004 kWh (by 71%) per one gram of COD treatment. Results confirmed that the chemical coagulants could increase the POME treatment efficiency and reduce the specific energy consumption of EF. However, this method can be improved aiming at further reduction of COD by mineralizing the dissolved organic compounds to fulfill the POME discharge quality standards.