Katie DiDominic

Dr. Katie DiDominic

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2019 in Journal of Hazardous, Toxic, and Radioactive Waste
Verified
Journal Article
Open access
KDKatie DiDominic
Katie DiDominic
MMMartina Morris
Martina Morris
SBShobha K. Bhatia
Shobha K. Bhatia
MKMahmoud M. Khachan
Mahmoud M. Khachan
KLKatharine E. Lewis
Katharine E. Lewis
Geotextile tubes with polyacrylamide flocculants are widely used in dewatering applications. Due to variations in solid concentrations during dredging, excess flocculant is sometimes released into the environment, where it might have toxic effects. This study determined optimum doses for a cationic polyacrylamide (CPAM) and a natural-based polymer alternative, cationic starch (C. Starch). Slurry samples were treated with optimum and 50% overdoses of each compound, and residual polymer concentrations were measured. Overdosed C. Starch resulted in low residuals (<2  ppm ), but overdosed CPAM resulted in 17.4 ppm residual polymer. The relative toxicity of CPAM and C. Starch was also tested using zebrafish embryos. 100% of embryos that had their chorion removed and 71.8% of embryos that retained their chorions were dead or dying after 7 days of exposure to CPAM. In contrast, there was no statistically significant difference in the numbers of embryos that were dead or dying when exposed to C. Starch compared with controls. These data strongly suggest that C. Starch should be considered as a replacement for CPAM in dewatering applications.

4 December 2025 in Glacies
Verified
Journal Article
Open access
PDF file
KDKatie DiDominic
Katie DiDominic
MOMargarita Ordaz
Margarita Ordaz
TMTerry Douglas Melendy
Terry Douglas Melendy
CCChrestien M. Charlebois
Chrestien M. Charlebois
Accurate assessment of compacted snow strength is critical for ensuring the safety and performance of snow runways in cold environments. The Russian Snow Penetrometer (RSP) is widely used in snow science and engineering due to its simplicity, portability, and capability for rapid field measurements under extreme conditions. Conversely, the California Bearing Ratio (CBR) test remains the benchmark for evaluating the load-bearing capacity of conventional granular materials but is seldom applied to snow because of logistical constraints and the material’s complex mechanical behavior. The relationship between these two pavement evaluation tools remains poorly defined. This work investigates how RSP strength indices relate to CBR measurements to determine whether the RSP can serve as a practical proxy for snow pavement load-bearing capacity. Side-by-side field measurements of snow pavement strength were collected over a 30 h period at two test section locations. Both methods captured temporal strength increases and spatial variability, with consistently higher values at the second site attributed to extended sintering. A moderate linear correlation (R2 = 0.44) between RSP and CBR results supports a quantifiable relationship between the two methods. These findings begin to bridge the gap between conventional pavement testing and snow-specific strength evaluation, demonstrating the potential of the RSP for rapid assessment of snow runways. Continued data collection and analysis will refine this relationship and strengthen its applicability for operational use.

16 July 2024 in Journal of Environmental Quality
Verified
Journal Article
Open access
KDKatie DiDominic
Katie DiDominic
JSJames P. Shapleigh
James P. Shapleigh
MWM. Todd Walter
M. Todd Walter
YWY. Samuel Wang
Y. Samuel Wang
MRMatthew C. Reid
Matthew C. Reid
JRJohn M. Regan
John M. Regan
Excessive amounts of nitrogen (N) and phosphorus (P) can lead to eutrophication in water sources. Woodchip bioreactors have shown success in removing N from agricultural runoff, but less is known regarding P removal. Woodchip bioreactors are subsurface basins filled with woodchips installed downgradient of agricultural land to collect and treat drainage runoff. Microorganisms use the woodchips as a carbon (C) source to transform N in the runoff, with unresolved biological impacts on P. This study aims to explore microbial communities present in the bioreactor and determine whether milling woodchips to probe the microbial communities within them reveals hidden microbial diversities or potential activities. Metagenomic sequencing and bioinformatic analyses were performed on six woodchip samples (i.e., three unmilled and three milled) collected from a 10‐year‐old woodchip bioreactor treating agricultural tile drainage. All samples had similar DNA purity, yield, quality, and microbial diversity regardless of milling. However, when sequences were aligned against various protein libraries, our results indicated greater relative abundance of denitrification and P transformation proteins on the outside of the woodchips (unmilled), while the interior of woodchips (milled) exhibited more functional gene abundance for carbohydrate breakdown. Thus, it may be important to characterize microbial communities both within woodchips, and on woodchip surfaces, to gain a more holistic understanding of coupled biogeochemical cycles on N, P, and C in woodchip bioreactors. Based on these findings, we advise that future microbial research on woodchips (and potentially other permeable organic materials) examine both the surface biofilm and the interior organic material during initial studies. Once researchers determine where specific proteins or enzymes of interest are most prevalent, subsequent studies may then focus on either one or both aspects, as needed.

15 November 2025 in Glacies
Verified
Journal Article
Open access
PDF file
KDKatie DiDominic
Katie DiDominic
TMTerry Douglas Melendy
Terry Douglas Melendy
CCChrestien M. Charlebois
Chrestien M. Charlebois
Snow construction plays a crucial role in military operations in cold regions, providing tactical fortifications, thermal insulation, and emergency infrastructure in environments where conventional building materials are scarce or require extensive infrastructure for support. Current snow construction methods, including manual piling and compaction, are labor-intensive and inconsistent, limiting their use in large-scale or time-sensitive operations. This study explores the feasibility of adapting a compressed earth block (CEB) machine to produce compressed snow blocks (CSBs) as modular, uniform building units for cold-region applications. Using an AECT Impact 2001A hydraulic press, naturally occurring snow was processed with a snowblower and compacted at maximum operating pressure (i.e., 20,684 kPa) to evaluate block formation, dimensional consistency, and density. The machine successfully produced relatively consistent CSBs, but the initial 3–4 blocks following block height adjustment were generally unsuccessful (e.g., incorrect block height or collapsed/broke) while the machine reached its steady state cyclic condition. These blocks were discarded and excluded from the dataset. The successful CSBs had mean block heights of 7.76 ± 0.56 cm and densities comparable to ice (i.e., 0.83 g/cm3). Variations in block height and mass may be attributed to manual snow loading and minor material impurities. While the dataset is limited, the results warrant further investigation into this technology, particularly regarding CSB strength (i.e., hardness and compressive strength) and performance under variable snow and environmental conditions. Mechanized snow compaction using existing CEB technology is technically feasible and capable of producing uniform, structurally stable CSBs but requires further investigation and modifications to reach its full potential. With design improvements such as automated snow feeding, cold-resistant components, and system winterization, this approach could enable scalable CSB production for rapid, on-site construction of snow-based structures in Arctic environments, supporting the military and civilian needs.

31 October 2025 in Preprints.org
Verified
Preprint
Open access
PDF file
KDKatie DiDominic
Katie DiDominic
MOMargarita Ordaz
Margarita Ordaz
TMTerry Douglas Melendy
Terry Douglas Melendy
CCChrestien M. Charlebois
Chrestien M. Charlebois
Accurate assessment of compacted snow strength is critical for ensuring the safety and performance of snow runways in cold environments. The Russian Snow Penetrometer (RSP) is widely used in snow science and engineering due to its simplicity, portability, and capability for rapid field measurements under extreme conditions. Conversely, the California Bearing Ratio (CBR) test remains the benchmark for evaluating load-bearing capacity of conventional granular materials but is seldom applied to snow because of logistical constraints and the material’s complex mechanical behavior. To address this gap, this study presents side-by-side field measurements of snow pavement strength using RSP and CBR over a 30-hr period at two test section locations. Both methods captured temporal strength increases and spatial variability, with consistently higher values at the second site attributed to extended sintering. A moderate linear correlation (R² = 0.44) between RSP and CBR results confirms RSP’s potential as a proxy for load-bearing capacity in snow-covered terrains. These findings contribute to bridging the gap between traditional pavement testing and snow-specific methods, advancing the development of robust, rapid assessment tools for snow runway design and safety. Ongoing work aims to expand the dataset of paired RSP and CBR measurements to refine this relationship and establish a reliable conversion framework for operational use.