Kamal Gautam

Mr. Kamal Gautam

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 February 2026 in Journal of the Mechanical Behavior of Biomedical Materials
Verified
Journal Article
Open access
Kamal GautamKamal Gautam
Kamal Gautam
HJHector Gomez Jimenez
Hector Gomez Jimenez
YDYusuf Dikici
Yusuf Dikici
JBJay Bensusan
Jay Bensusan
GWGary E. Wnek
Gary E. Wnek
OAOzan Akkus
Ozan Akkus
PLGA/HA is a promising material for 3D printed bioresorbable bone scaffolds, but the effects of fused filament fabrication parameters on monotonic and cyclic mechanical performance of resulting structures are unknown. Furthermore, the evolution of mechanical properties and dimensional stability under prolonged exposure to temperature and cell culture immersion conditions is also poorly investigated. This study first applied a Taguchi L9 orthogonal array to evaluate the effects of layer height, nozzle temperature, print speed, and cooling fan speed on the flexural properties of 90:10 wt% PLGA/HA scaffolds. Statistical analysis revealed that flexural strength, modulus, and deflection at failure were significantly influenced by specific printing parameters, while energy absorption showed no significant dependence (p > 0.05). At 50% print porosity, flexural strength and modulus increased by 20% and 50%, respectively, under the optimal settings (0.12 mm layer height and 205 °C nozzle temperature), reaching 45.0 MPa and 1807.80 MPa. Differential scanning calorimetry revealed significant effects on second-cycle glass transition (p = 0.0029), first-cycle cold crystallization (p = 0.0086), second-cycle cold crystallization (p = 0.0177), and first-cycle crystallinity (p = 0.0177), with favorable transitions aligning with mechanical maxima. Fatigue samples were printed using parameters that provided maximum flexural strength, and tests in PBS at 37 °C showed an endurance limit of 1.2 MPa at 106 cycles. In-vitro degradation over 60 days caused swelling of the scaffold by more than 20%, while the strength and the modulus decreased by 76% and 65% respectively, still above lower levels for trabecular bone. Consequently, optimization of 3D print parameters resulted in attaining improved mechanical properties of PLGA/HA, making scaffolds printed under these conditions viable for partial load bearing bone tissue regeneration applications.

26 June 2024 in International Journal of Research in Orthopaedics
Verified
Journal Article
Open access
PDF file
Kamal GautamKamal Gautam
Kamal Gautam
MHMohamed S. Hefzy
Mohamed S. Hefzy
AMAbdul A. Mustapha
Abdul A. Mustapha
BKBehrens Kyle
Behrens Kyle
Background: The study of muscle forces in upper extremities is pivotal for advancements in biomechanical modeling, contributing significantly to the field of orthopedics, rehabilitation, and sports science. Despite the prominence of OpenSim and AnyBody modeling system™ in this domain, a gap persists in comparative analyses specifically targeting muscle force predictions in upper extremity motions. Methods: This study compares the predictions of muscle forces in static elbow flexion, shoulder flexion, and shoulder abduction using OpenSim and AnyBody modeling systemTM, hypothesizing significant differences in predictions attributable to their distinct modeling methodologies and assumptions. This work utilized generic models without subject-specific data and conducted simulations in both software environments, focusing on the magnitude and activation of major muscle forces under predefined kinematics. Results: OpenSim and AnyBody modeling systemTM produced similar results when simulating elbow flexion, with both software predicting forces in the major muscles required to maintain the posture. However, discrepancies were observed between the two software for muscle force predictions during the shoulder flexion and abduction movements. AnyBody modeling systemTM appeared to be more robust as it included all the upper extremity muscles and predicted the major muscles forces required for these movements more accurately compared to OpenSim. Conclusions: The results of this study show significant differences in muscle force predictions between OpenSim and AnyBody modeling systemTM, attributed to the unique modeling approaches, especially in representing muscle-tendon complexes and joint dynamics.

20 January 2025 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Kamal GautamKamal Gautam
Kamal Gautam
MHMohamed Samir Hefzy
Mohamed Samir Hefzy
KBKyle Behrens
Kyle Behrens
AMAbdul A. Mustapha
Abdul A. Mustapha
Acromioclavicular joint osteoarthritis is prevalent in middle-aged and older people, causing shoulder pain and functional limitations. Despite its prevalence, there are inconsistencies in the physical diagnosis procedures practiced in clinical tests. A recent study introduced a novel hand-behind-the-back (HBB) test, a promising alternative to the traditional cross-body adduction (CBA) test. However, further study was suggested to validate the results obtained. So, this study predicted muscle forces for the cross-body adduction and hand-behind-the-back tests using OpenSim and the AnyBody Modeling System™. This work redefined the joint kinematics for the tests and performed an inverse dynamics analysis to solve the muscle redundancy problem using the generic upper extremity dynamic models available in OpenSim and AnyBody Modeling System™. The results revealed some agreements and significant discrepancies in most muscle force predictions between the OpenSim and AnyBody Modeling SystemTM. Thus, this study underscores the necessity of integrating multiple modeling approaches and comprehensive validation, including experimental data, to enhance the accuracy and reliability of muscle force predictions in shoulder biomechanics during CBA and HBB tests.

25 June 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
YDYusuf Dikici
Yusuf Dikici
Kamal GautamKamal Gautam
Kamal Gautam
HJHector Jimenez
Hector Jimenez
ASAlan Shepardson
Alan Shepardson
MZMaximilian Zernic
Maximilian Zernic
OAOzan Akkus
Ozan Akkus
Osteochondral repair remains constrained by a lack of scaffolds that simultaneously achieve high porosity, native-like biomechanics, long-term fatigue resistance, and stable integration between cartilage- and bone-facing zones. To address these challenges, this study introduces the Osteochondral Articular Lining Textile (OCALT), a novel, biodegradable three-dimensional spacer fabric fabricated by weft-knitting poly(lactic-co-glycolic acid) (PLGA) monofilaments. To provide an anchoring subchondral interface, a PLGA bone backing was directly 3D printed onto the textile using fused filament fabrication, resulting in adhesive-free polymer interpenetration and a mechanically coherent osteochondral interface. Three yarn architectures were evaluated in terms of their effects on mechanical properties of the spacer fabric. All OCALT configurations exhibited exceptional porosity exceeding 80%, providing an interconnected void space for tissue ingrowth. Using double-ply yarn in the spacer layer increased compressive stiffness by up to 114%, whereas using double-ply yarn in the subchondral layer enhanced tensile modulus and fabric-to-backing adhesion by more than 115% and 40%, respectively. The configuration featuring double-yarn reinforcement in both the spacer and subchondral layers delivered the most balanced performance in terms of elastic recovery, tensile stiffness, interfacial toughness, and a compressive modulus that remained stable even after one million accelerated loading cycles. These findings establish OCALT as a highly tunable, scalable, and resilient 3D-textile platform capable of meeting the complex mechanical and structural demands of cartilage regeneration.

1 March 2023 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
SMS Malesh
S Malesh
Kamal GautamKamal Gautam
Kamal Gautam
JYJ Yaman
J Yaman
BBB Bivek
B Bivek
Concerns about building thermal performance and energy consumption are fast growing as they account for roughly 40% of worldwide annual energy use. Building construction in Nepal is controlled by the National Building Codes (NBC), which focus solely on structural considerations and ignore thermal behaviour. As a result, housing tends to be too much warm and too cold during summer and winter respectively due to the lack of passive heating and cooling mechanisms considered during the construction phase. The Thakle Integrated Settle (TIS), built by the Department of Urban Development and Building Construction (DUDBC) under the National Reconstruction Authority and supported by Oxfam Nepal, was the subject of this research. The building’s performance in the chosen location was analysed using a field and TRNSY simulation-based technique. Using meteorological data from Meteonorm software, the TRNSYS model was created to examine the performance in terms of internal air temperature and heating/cooling load of two buildings with different orientations, e.g., North-East (NE) and South-West (SW). According to simulation results, there is a heating demand that covers roughly 37% of the year, while cooling and comfort conditions were 32% and 31%, respectively. For NE and SW-facing buildings, heating demand was 4.10 MWh and 4.07 MWh, while cooling demand was 1.302 MWh and 1.309 MWh respectively.