The article deals with the novel printed log-periodic antenna. It contains a printed assembly of the so-called center-end-fed dipole-like stretched radiators. The modified printed-circuit-board two-layer topology of the power splitter is proposed in order to excite the modified log-periodic dipole-like antenna composed of the center-end-fed dipole-like radiator. This splitter is based on the slot-line-microstrip transitions. The systematic analysis of the splitter as well as the log-periodic array itself is presented. All the key geometrical dimensions are derived through the nonlinear parametric optimization using the 3D full-wave solver like “CST Studio Suite”. Prior to implementation of the whole printed log-periodic antenna, the main fragments of that were manufactured and successfully tested. The experimental results agree well with the simulation-derived ones. The incorporation of proposed splitter and radiator into design procedures leads to increase the degree of freedom in microwave region that paves a way for next generation of the ultra-wideband microwave antennas.
This article analyses a dipole–like radiator with a center–end feed. In this paper, there are expressions describing the electrodynamic properties of such a radiator. A part of the expression for the radiation resistance of the center–end fed dipole–like radiator in closed form is obtained. Also based on the method of induced electromotive forces, equations for the complex input resistance of the transmitter in free space were obtained. Based on the results of the calculations, plots of the real and imaginary parts of the complex input impedance of the center–end fed dipole–like radiator against its relative length were plotted, which were used further to form the initial topology of the printed antenna. The electrodynamic model of the printed antenna, which is distinguished by a high degree of directionality and matching with a 50 Ohm cable, is given. The bandwidth of the printed antenna is about 10% of the operating frequency. The proposed center-end feed dipole-like radiator may be used in director antennas, phased antenna arrays, turnstile and cardioid radiators, and other multi-dipole antenna systems.
This article deals with the systematic approach based on two following topics. The first one describes the newly proposed S-band 8x8 dividing-summating architecture employing the asymmetric two-section backward-wave strip-line directional couplers. The corresponding network is manufactured by using the standard two-layer printed circuit board technology. The variety of the insertion losses through the any channels is less than 0.8 dB whereas the phase difference through those is less than 15 degrees. This circuit was successfully used to excite the novel printed log-periodic satellite antenna that was realized on a base of the array of the various center-end-fed dipole-like radiators proposed earlier in Russian Patent no. 2571156, date of Patent Dec. 20, 2015. The detailed design procedure of this log-periodic aerial relates to the second topic. In addition, the results of computer modeling by using the “CST Studio Suite” solver are presented and discussed in details. Both the proposed printed circuit units are the good candidates for next generation of the microwave satellite communications.
1 July 2024 in Journal of the Russian Universities. Radioelectronics
Introduction. The topic of implementing a dual-band mode of operation for director dipole antennas is represented by a wide range of works, almost all of which are dedicated to studying the properties of a classic dipole. However, the issue of end excitation of radiators for dual-band director antennas remains open. The development of such radiators requires a deep analysis both from the point of view of developing mathematical and electrodynamics models, which corresponds to the tactical and technical requirements of modern digital antenna arrays.Aim. To substantiate a procedure for determining the initial appearance of a dual-band antenna exciter from the standpoint of the systems approach to the design of antenna elements and nodes. This procedure is suitable for a semi-automated design of more complex antenna systems.Materials and methods. As part of the research, the input impedance of a dual-band system consisting of two active radiators and two passive directors was determined using the method of induced electromotive forces (EMF). Models of dual-band director radiators were developed using the CST Studio Suite 2021 full-wave electromagnetic simulation.Results. The results of developing procedures for a semi-automatic design of antennas with a dual-band function of input impedance are presented. Following a comparative analysis, approaches to implementing the printed layout of an antenna comprising standard radio engineering components, which imply serial production, are proposed.Conclusion. The proposed models can be used when designing director, turnstile, and cardioid antennas, as well as antenna arrays. These designs are analogous to antennas based on a classic central excited dipole.
A model of a dual-band microstrip antenna array based on a dipole radiator with end excitation is proposed and analyzed in terms of electrodynamic antenna