The study is focused on the manufacturing of fully dense and porous Ti6Al4V parts by Powder Bed Fusion (PBF) method. In the scope of the study, the reasons of the impact of the powder recoating system and internal stress-induced failures in the manufacturing of tensile specimens were investigated and solution proposals were presented. Results that were determined by implementing the most suitable solution were investigated. In this study, failures that occurred during manufacturing were prevented by analyzing the powder recoating system. As a result of the study, the negative effects, which were caused by the impact of the recoater blade on the parts, were prevented. It was observed that the samples were bent due to the forces that were generated by the recoating system movement during manufacturing. The bending conditions were eliminated when the samples were manufactured in a barrel. Thus, no deformation occurred in the part. The negative effects of internal stresses in samples were removed by using the cooling rate concept and FEA analysis. Finally, assumptions of simulations were verified by manufacturing samples with the same machine parameters.
This study focuses on optimizing machining parameters in the micro-milling of AlSi10Mg aluminum alloy produced via the powder bed fusion additive manufacturing process. Although additive manufacturing enables complex geometries and minimizes material waste, challenges remain in reducing surface roughness and cutting forces during post-processing. Micro-milling experiments were conducted using spindle speeds up to 60,000 rpm, with varied feed rates and cutting depths. Cutting forces (Fx, Fy, and Fz) were measured using a Kistler-9119AA1 mini dynamometer, while surface roughness (Ra) was evaluated with a Nanovea-ST400 3D optical profilometer. Five advanced machine learning models, random forest regressor (RFR), gradient boosting regressor (GBR), LightGBM, CatBoost, and k-nearest neighbors (KNN), were employed to predict cutting forces and surface roughness, with CatBoost achieving the highest predictive accuracy (R2 > 0.96). Among all models, CatBoost achieved the best predictive performance, with test R2 values exceeding 0.96 for both force and Ra estimations. Experimental and ML-based results demonstrated that higher feed rates and depths of cut increased cutting forces, particularly in the Fx direction, while elevated spindle speeds reduced forces due to thermal softening. Surface roughness was minimized at lower feed rates and higher spindle speeds. The optimal machining conditions for achieving Ra < 1 µm were identified as ap = 50 µm, n = 30,000 rpm, and fz = 0.25 µm/tooth. This integrated approach supports precision machining of AM aluminum alloys.
3 January 2022 in Journal of the Mechanical Behavior of Biomedical Materials
In industrial manufacturing and research laboratories, precise machining of work materials is crucial to meet the demand for fast assembly and sustainable high-quality production. Precise machining procedures play a vital role in manufacturing compatible parts that meet the production requirements. This study investigates the impact of different parameters on burr formations and slot dimensions during the micro-milling of AISI 316 material. A careful examination was conducted using scanning electron microscopy (SEM) images under varying conditions. The variables considered include cutting speed, feed rate, and depth of cut. The main finding revealed that the feed rate and depth of cut significantly influence burr formation, with lower rates and depths resulting in noticeable reductions. A higher feed rate was associated with more pronounced burr formation. Moreover, burr widths on the down-milling sides were typically wider than those on the up-milling sides due to continuous chip formation and compressive forces during down-milling. Utilizing image processing, the study further quantified burr and slot widths with high accuracy, offering a reliable method to characterize burr formation. This research presents potential ways to minimize burr formation during micro-milling processes by effectively managing machining parameters.
In this study, samples manufactured with polylactic acid (PLA) plastic material using the fused deposition modeling (FDM) type printer were analyzed during the manufacturing process using image processing and real-time big data analysis. The purpose of real-time big data analysis is to provide an effective and efficient guide to the user in the manufacturing process regarding the manufactured part’s mechanical properties. In this study, compression samples were prepared according to ASTM D695-15, Standard Test Method for Compressive Properties of Rigid Plastics, test standards and subjected to mechanical tests. In the first stage of the research, using artificial neural networks (ANNs), processing parameters were estimated with 92.5 % accuracy according to the R2 performance evaluation criterion. In the second stage, each layer’s infill percentage and layer thickness of the compression sample were analyzed using image processing techniques. In the final stage of the study, using the Python programming language, a user-specific visual interface is designed for showing the results and graphics related to the material processing step in FDM 3D printing.
14 April 2021 in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
In this study, a sample part is manufactured by using the Powder Bed Fusion (PBF) method with maraging steel metal powder, and the manufactured part is examined in terms of dimensional accuracy by image processing techniques. The sample =art is drawn with various geometric shapes so that dimensional and areal controlling with the image processing techniques can be performed accurately. The purpose of dimensional control is to choose the most suitable manufacturing parameters to ensure the closest production of the real dimensions of the part. With the detection of significant deviations in dimensional values by image processing techniques, the designs of the part should be changed according to these deviations. In this study, each layer of the manufactured sample part image is captured by a camera. Afterward, dimensional and areal percent error rates are determined by three different methods based on image processing techniques.