Kourosh Tatar

Dr. Kourosh Tatar

Department of Industrial Management, Industrial Design and Mechanical Engineering, University of Gävle, Gävle, Gävleborg, Sweden
orcid

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2008 in International Journal of Machine Tools and Manufacture
Verified
Journal Article
Closed access
Kourosh TatarKourosh Tatar
Kourosh Tatar
PGPer Gren
Per Gren

1 August 2009 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
SPSilvio Pappadà
Silvio Pappadà
PGPer Gren
Per Gren
Kourosh TatarKourosh Tatar
Kourosh Tatar
TGTord Gustafson
Tord Gustafson
RRRocco Rametta
Rocco Rametta
Alfonso MaffezzoliAlfonso Maffezzoli
Alfonso Maffezzoli

1 May 2007 in Mechanical Systems and Signal Processing
Verified
Journal Article
Closed access
Kourosh TatarKourosh Tatar
Kourosh Tatar
MRMatti Rantatalo
Matti Rantatalo
PGPer Gren
Per Gren

10 February 2006 in Measurement Science and Technology
Verified
Journal Article
Closed access
PGPer Gren
Per Gren
Kourosh TatarKourosh Tatar
Kourosh Tatar
JGJan Granström
Jan Granström
NMN-E Molin
N-E Molin
EJErik V Jansson
Erik V Jansson

4 March 2021 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Open access
PDF file
ISInge Svenningsson
Inge Svenningsson
Kourosh TatarKourosh Tatar
Kourosh Tatar
The paper reveals a hypothesis regarding the adhesive mechanism in metal cutting and its mechanical dynamics. One steel grade, 34CrNiMo 6, 285 HB, and one set of coatings on the cutting tool are reviewed. The adhesive mechanism is a transient vibration, including a feedback system limited by the plastic deformation in the chip. The vibration shows as a cluster of waves with stochastic duration in time. It starts up again after a stochastic lapse of silence. The cycle frequency is around 12.5 kHz and the internal excitation is twice that frequency, as the cutting speed and feed are 200 m/min and 0.2 mm, respectively. The adhesive frequency and amplitude are influenced by the cutting speed and the current wear status. The adhesion is monitored by the sound waves emanating from vibrations in the chip, the part still in the workpiece.

13 June 2023 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Open access
PDF file
ISInge Svenningsson
Inge Svenningsson
Kourosh TatarKourosh Tatar
Kourosh Tatar
The deterioration of the cutting edge during machining influences production cost and productivity. The adhesion is one of the main wear mechanisms. This study delves into the adhesive mechanism in the context of turning, milling, and drilling, focusing on three different cutting materials: 34CrNiMo6, 1.437 stainless steel, and ductile iron. Building upon previous research on the adhesive process in turning, a dynamic model was developed to understand the mechanism further. The results showed that adhesion is a general phenomenon occurring in all tested work materials, but with varying intensity levels. Intermittent cuts did not greatly impact the adhesive mechanism, and cutting data, coolant, and chip breaking also showed little effect. However, the presence of graphite in ductile iron temporarily inhibited adhesion. The source of the adhesive sound was found to be the pivoting movement of the chip as it binds and rips off the cutting tool, leading to a frequency shift upon detachment. The adhesive wear was found to be a thermal mechanism, where chemical reactions between the SiO2 in the work material with the cutting tool caused thermal cracks and low-frequency fatigue.