Kshitij Shrestha

Dr. Kshitij Shrestha

Nagoya City University
orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2017 in Journal of Composites for Construction
Verified
Journal Article
Closed access
UEUsama Ebead
Usama Ebead
KSKshitij Shrestha
Kshitij Shrestha
MAMuhammad S. Afzal
Muhammad S. Afzal
ARAhmed El Refai
Ahmed El Refai
ANAntonio Nanni
Antonio Nanni
This paper reports on the efficiency of fabric-reinforced cementitious matrix (FRCM) in enhancing the flexural capacity and deformational characteristics of RC beams. In the main experimental part of the paper, 12 RC beams, 2,500 mm long, 150 mm wide, and 260 mm deep, were fabricated. The beams had two different steel reinforcement ratios, namely, ρsD12=0.72% and ρsD16=1.27%, representing typical underreinforced beam sections. The strengthened beams utilized two FRCM types, carbon and polyparaphenylene benzobisoxazole (PBO) FRCM systems. In the second part of the work, tensile material characterization tests were performed on the FRCM coupons to determine the tensile characteristics of the FRCM composites. The beams were tested in flexure under four-point loading until failure. Two beams without FRCM strengthening were used as a benchmark. Six beams were externally strengthened using one, two, and three layers of carbon FRCM system. Four beams were strengthened with one and two layers of PBO FRCM ...

1 October 2017 in Construction and Building Materials
Verified
Journal Article
Closed access
AYAdel Younis
Adel Younis
UEUsama Ebead
Usama Ebead
KSKshitij Shrestha
Kshitij Shrestha

25 January 2013 in Smart Materials and Structures
Verified
Journal Article
Closed access
KSKshitij Shrestha
Kshitij Shrestha
YAYoshikazu Araki
Yoshikazu Araki
TNTakuya Nagae
Takuya Nagae
YKYuji Koetaka
Yuji Koetaka
YSYusuke Suzuki
Yusuke Suzuki
KIKiyohito Ishida
Kiyohito Ishida

16 September 2015 in Earthquake Engineering & Structural Dynamics
Verified
Journal Article
Closed access
PDF file
YAYoshikazu Araki
Yoshikazu Araki
KSKshitij Shrestha
Kshitij Shrestha
NMNao Maekawa
Nao Maekawa
YKYuji Koetaka
Yuji Koetaka
TOToshihiro Omori
Toshihiro Omori
RKRyosuke Kainuma
Ryosuke Kainuma

12 February 2014 in Structural Control and Health Monitoring
Verified
Journal Article
Closed access
PDF file
YAYoshikazu Araki
Yoshikazu Araki
NMNao Maekawa
Nao Maekawa
KSKshitij Shrestha
Kshitij Shrestha
MYMakoto Yamakawa
Makoto Yamakawa
YKYuji Koetaka
Yuji Koetaka
RKRyosuke Kainuma
Ryosuke Kainuma
This paper investigates the feasibility of tension braces using Cu–Al–Mn superelastic alloy bars as energy dissipating and self‐centering elements for steel frames by performing 1/3 scale shaking table tests. The difficulty with conventional steel tension braces lies in pinching or significant deterioration of stiffness and strength under cyclic loading. When a steel frame with conventional tension braces is subjected to intense earthquakes, pinching may lead to a large residual drift and/or instability. To overcome the difficulty, this paper examines the effectiveness of Cu–Al–Mn superelastic alloy bars, facilitated by their large recovery strain, low material cost, and high machinability, as a partial replacement of steel bars in tension braces. In the shaking table tests, a 1/3 scaled 1‐bay, 1‐story steel frame with the present tension braces is subjected to quasi‐static cyclic loading and dynamic harmonic ground motions of 6 Hz. Both the static and dynamic test results demonstrate the effectiveness of the present braces in avoiding pinching under the ductility ratio up to 3. The dynamic test results also demonstrate the capability of the present tension braces in reducing the peak response acceleration within the base shear capacity. To study the rate dependence of the frame response, further, time‐history analyses are performed by using a SDOF model based on a uniaxial rate‐independent model, calibrated with the quasi‐static tests. A comparison of the analytical results with the dynamic test results demonstrates that the rate dependence of the frame response is negligible up to the loading frequency of 6 Hz. Copyright © 2014 John Wiley & Sons, Ltd.

23 January 2015 in Smart Materials and Structures
Verified
Journal Article
Closed access
PDF file
KSKshitij Shrestha
Kshitij Shrestha
MSM Saiid Saiidi
M Saiid Saiidi
CCCarlos A Cruz
Carlos A Cruz
This paper presents analytical modeling to study the seismic response of bridge systems with conventional and advanced details. For validation, a 33 m quarter-scale model of a four-span bridge incorporating innovative materials and details seismically tested on the shake tables at the University of Nevada, Reno was taken. The bridge specimen involved use of advanced materials and details to reduce damage at plastic hinges and minimize residual displacements. A three-dimensional, nonlinear model incorporating the response of the innovative materials was developed to study the bridge response using the finite-element software OpenSees. Existing finite-element formulations were used to capture the response of the advanced materials used in the bridge. The analytical model was found to be able to reproduce comparable bent displacements and bent shear forces within reasonable accuracy. The validated model was further used to study different types of bridges under suite of scaled bi-directional near-fault ground motions. Comparisons were made on behavior of five different bridge types, first conventional reinforced concrete bridge, second post-tensioned column bridge, third bridge with elastomeric rubber elements at the plastic hinge zone, fourth bridge with nickel–titanium superelastic shape memory alloy (SMA) reinforcing bar and fifth bridge with CuAlMn superelastic SMA reinforcing bar. Both the SMA used bridges also utilized engineered cementitious composite element at the plastic hinge zone. The results showed effectiveness of the innovative interventions on the bridges in providing excellent recentering capabilities with minimal damage to the columns.