Kudret Irem Deniz

Ms. Kudret Irem Deniz

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 March 2023 in Pharmaceutics
Verified
Journal Article
Open access
PDF file
MAMusa Ayran
Musa Ayran
HKHatice Karabulut
Hatice Karabulut
KDKudret Irem Deniz
Kudret Irem Deniz
GAGamze Ceren Akcanli
Gamze Ceren Akcanli
Songul UlagSongul Ulag
Songul Ulag
Anton FICAIAnton FICAI
Anton FICAI
Skeletal muscle tissue engineering presents a promising avenue to address the limitations pertaining to the regenerative potential of stem cells in case of injury or damage. The objective of this research was to evaluate the effects of utilizing novel microfibrous scaffolds, containing the compound quercetin (Q), on skeletal muscle regeneration. Morphological test results showed us that the combination of bismuth ferrite (BFO), polycaprolactone (PCL), and Q were bonded and well-ordered with each other, and a uniform microfibrous structure was obtained. Antimicrobial susceptibility testing of PCL/BFO/Q was conducted, and microbial reduction was found to be over 90% in the highest concentration of Q-loaded microfibrous scaffolds with the most inhibitory effect on S. aureus strains. Further, biocompatibility was investigated by performing MTT testing, fluorescence testing, and SEM imaging on mesenchymal stem cells (MSCs) to determine whether they could act as suitable microfibrous scaffolds for skeletal muscle tissue engineering. Incremental changes in the concentration of Q led to increased strength and strain, allowing muscles to withstand stretching during the healing process. In addition, electrically conductive microfibrous scaffolds enhanced the drug release capability by revealing that Q can be released significantly more quickly by applying the appropriate electric field, compared with conventional drug-release techniques. These findings suggest a possible use for PCL/BFO/Q microfibrous scaffolds in skeletal muscle regeneration by demonstrating that the combined action of both guidance biomaterials was more successful than Q itself acting alone.

Verified
Journal Article
Open access
PDF file
Luca GiorleoLuca Giorleo
Luca Giorleo
KDKudret Irem Deniz
Kudret Irem Deniz
Sheet metal forming is a widely used manufacturing process, but the high cost and long production time of traditional forming tools limit its flexibility, especially for prototyping and small-batch production. Additive manufacturing offers a promising alternative, enabling the rapid and cost-effective fabrication of customized tools. In this study, bending tools were produced using Fused Filament Fabrication and optimized through a topology optimization approach. A combined experimental and numerical approach was applied to validate standard tool geometries and extract load conditions for use in a topology optimization process. The resulting optimized punch and die achieved a mass reduction of approximately 50% while maintaining structural integrity and safety factors well above critical thresholds. Finite Element Analysis revealed an increase in elastic deformation and stress concentration in non-critical regions, without compromising tool functionality. Experimental tests with the optimized tools confirmed their suitability for sheet metal bending, although a decrease of about 2° in the bending angle and an increase in variability were observed, consistent with simulation results. The study demonstrates the feasibility of using topology-optimized polymer tools for low-volume forming applications, offering a lightweight, cost-effective, and sustainable alternative to traditional metal tooling.

Verified
Journal Article
Open access
PDF file
Luca GiorleoLuca Giorleo
Luca Giorleo
KDKudret Irem Deniz
Kudret Irem Deniz
Rapid tooling with polymer tools produced via additive manufacturing offers significant benefits in sheet metal forming processes as it allows for the production of parts with high accuracy while reducing tool production costs. In this research, the authors evaluate the performance of polymer punches and dies in the sheet metal bending of 2 mm thick AISI 314 stainless steel. The tools were made using nylon filled with carbon fiber and produced through Fused Filament Fabrication. Two different print orientations—horizontal and vertical—were compared. This experimental study focused on the accuracy of the sheet’s bending angle and thickness while also measuring the deformation induced in the tools. A new methodology was proposed combining both tools and sheet measures to highlight not only the sheet’s accuracy but also the behavior of the polymer tools. The results demonstrate that despite the permanent deformation of the tools, they were able to produce sheets with a geometry accuracy of less than 0.5%

12 October 2026 in Polymer Engineering & Science
Verified
Journal Article
Closed access
KDKudret Irem Deniz
Kudret Irem Deniz
Luca GiorleoLuca Giorleo
Luca Giorleo
Luciana SartoreLuciana Sartore
Luciana Sartore
SUSongul Ulag
Songul Ulag
ASAli Sahin
Ali Sahin
Oguzhan GunduzOguzhan Gunduz
Oguzhan Gunduz