Laura Tonni

Prof. Laura Tonni

orcid

Research Focus & Metrics

Academic Career Length

24Years (2003-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2022 in Journal of Geotechnical and Geoenvironmental Engineering
Verified
Journal Article
Closed access
PDF file
SASara Amoroso
Sara Amoroso
MMMaria F. García Martínez
Maria F. García Martínez
PMPaola Monaco
Paola Monaco
LTLaura Tonni
Laura Tonni
GGGuido Gottardi
Guido Gottardi
KWKord J. Wissmann
Kord J. Wissmann
Following the 2012 Emilia-Romagna seismic sequence, widespread liquefaction of silty sands was observed, providing the opportunity to enhance our knowledge of the influence of fines content on seismic hazard and mitigation works. This paper presents the results of a thorough geotechnical investigation performed in connection with full-scale controlled blast tests in Bondeno, Italy, a small village that suffered liquefaction in 2012. Piezocone (CPTU) and seismic dilatometer (SDMT) tests were performed in natural and improved soils after rammed aggregate pier (RAP) treatment to a depth of 9.5 m to provide accurate soil characterization, evaluate liquefaction, and verify the effectiveness of the ground improvement. The combined use of piezocone (CPTU) and flat dilatometer (DMT) data provided reliable estimates of the overconsolidation ratio and at-rest earth pressure coefficient and highlighted the soil improvement in silty sands between 4 and 9 m in depth. Shear-wave velocity measurements showed a low sensitivity to RAP installation. The treatment effectiveness was also confirmed by the use of the simplified procedures for liquefaction assessment, underlining the important influence of the adopted fines profile and by the blast-induced liquefaction. CPTU and DMT parameters remained approximately unchanged between the piers after the detonation.

9 February 2021 in Quarterly Journal of Engineering Geology and Hydrogeology
Verified
Journal Article
Closed access
MMMichela OF Marchi
Michela OF Marchi
MMMaría Fernanda García Martínez
María Fernanda García Martínez
GGGuido Gottardi
Guido Gottardi
LTLaura Tonni
Laura Tonni
Sand boils are the surface manifestation of an erosion process, known as backward erosion piping, which may take place beneath river embankments during high-water events. The risk of embankment failure greatly increases in locations affected by sand boils. Numerous studies have been carried out, mainly at the laboratory scale, providing significant advancements in this field. Nonetheless, there is still a gap between research and practice that needs to be filled. This study presents a set of field measurements carried out on a large sand boil reactivated near the toe of an embankment along the river Po, Italy. Hydraulic heads, velocity and discharge, concentration and pipe geometry were measured as a function of the water level in the river during the November 2018 flood. The collected data are compared with predictions of a theoretical model that provides the head loss in the vertical pipe. Furthermore, the local exit gradients, as deduced from measurements, are discussed, together with the operational critical gradients adopted in current design practice. The collected data provide important input parameters for the calibration of analytical and numerical models, typically implemented to investigate the sand boil evolution and then to assess the backward erosion piping risk at real scale.

1 January 2019 in AIMS Geosciences
Verified
Journal Article
Open access
PDF file
LTLaura Tonni
Laura Tonni
GGGuido Gottard
Guido Gottard
This paper explores the capability of cone penetration testing as an effective tool to estimate the compressibility characteristics of silts, silt mixtures and sand mixtures. The study uses part of the large amount of piezocone (CPTU) data and subsoil deformation measurements assembled over approximately 6 years at the Treporti Test Site (Venice, Italy), within an extensive research project aimed at thoroughly analyzing the stress-strain-time response of the complex assortment of sandy and silty sediments forming the Venetian lagoon subsoil. The combined analysis of piezocone data and subsoil deformations measured beneath a full-scale test embankment primarily showed that the existing interpretation approaches developed for 'standard' sands or clays - and thus based on the idealized assumption of fully drained or fully undrained testing conditions - generally result in invalid estimates of soil compressibility parameters. Therefore, site-specific correlations have been developed in order to correctly predict the compressibility of Venetian sediments, both primary and secondary, and consequently obtain the best fit of the measured settlements. By taking this very well documented case study as a base, the proposed paper aims at discussing some key issues on the use of piezocone tests for the geotechnical characterization of silts and other sedimentary soils with very scattered grain size distributions, thus falling in the so-called intermediate permeability range. The idea is basically to provide a critical appraisal of the CPTU-based approaches currently available for the mechanical characterization of natural soils, and explore potential advances in the interpretation methods, which might take account of possible partial drainage phenomena around the advancing cone during the test.

1 September 2013 in Geomechanics and Geoengineering
Verified
Journal Article
Closed access
LTLaura Tonni
Laura Tonni
PSPaolo Simonini
Paolo Simonini
The estimate of secondary compression behaviour of sandy and silty deposits is not routinely taken into account in the classical settlement calculation, due to its generally limited contribution to the total amount of strains. However, such soils exhibit a non-negligible time-dependent behaviour and the prediction of their long-term response may sometimes be important. This paper explores the capability of the piezocone test as an effective tool to estimate the one-dimensional secondary compression characteristics of sands and silts. The approach is mainly based on the observation that frictional response essentially governs both secondary compression of granular soils and cone resistance, hence it seems reasonable to establish a valid correlation among them. The study uses part of the field data assembled over the last years at the Treporti Test Site (Venice, Italy), within an extensive research project aimed at analysing the stress-strain-time response of the predominantly silty sediments forming the Venetian lagoon subsoil. Empirical, site-specific correlations for estimating the secondary compression coefficient from cone resistance are proposed. The regression analyses indicate that the estimate is slightly improved if the cone resistance-based correlations include a variable accounting for the different pore pressure response associated to the drainage conditions around the advancing cone.

1 December 2020 in Journal of Geotechnical and Geoenvironmental Engineering
Verified
Journal Article
Closed access
PDF file
MMMaría Fernanda García Martínez
María Fernanda García Martínez
LTLaura Tonni
Laura Tonni
MMMichela OF Marchi
Michela OF Marchi
STSimone Tozzi
Simone Tozzi
GGGuido Gottardi
Guido Gottardi
The article presents a three-dimensional (3D) finite element (FE) model of the groundwater flow beneath a river embankment, aimed at developing a simple and reliable numerical strategy for the identification of hydraulic conditions that cause the reactivation of sand boils in flood defense systems prone to recurrent backward erosion piping. The seepage model is calibrated on a cross section of the Po River, where a large natural sand boil has been periodically observed during past high-water events. Monitored river water levels, piezometric measurements, and geotechnical testing data have been used for the calibration study. The numerical analysis proposes a suitable way to simulate a preexisting eroded zone, identifies the key parameters to be collected in the field, and discusses the criteria for the assessment of piping reactivation. The sensitivity analysis proposed herein enables one to identify the set of model parameters capable of capturing field evidence.

13 May 2024 in Water
Verified
Journal Article
Open access
PDF file
LTLaura Tonni
Laura Tonni
MMMichela OF Marchi
Michela OF Marchi
ABAgnese Bassi
Agnese Bassi
ARAlessandro Rosso
Alessandro Rosso
Sand boil formation at the toe of river embankments is the typical manifestation of the initiation and progression of an internal erosion process known as backward erosion piping, which is recognized to be a major concern in many river systems worldwide. In Italy, more than 130 sand boils have been detected along the Po River, many of them experiencing recurrent reactivations during high-water events. In recent years, as part of the activities of the European project LIFE SandBoil, the Italian authority responsible for flood protection and flood damage reduction along the Po River has implemented a GIS-based web application to catalogue the sand boils observed in its operating area. The resulting database allows keeping records of a comprehensive and varied set of information, in terms of predisposing factors, initiation conditions and surface effects. Taking as a reference a well-documented cross-section of the Po River prone to piping, this paper describes the main features of this versatile and flexible tool, whose long-term aim is to support vulnerability studies and the development of risk maps against piping. The database, which might also accommodate data from different river basins, is thus meant to help in flood risk management, by suggesting priorities for the implementation of mitigation measures and allowing the monitoring of intervention effectiveness.