As a kind of cost-efficient hydrogen storage materials with high hydrogen capacity and light weight, Mg-based alloys have attracted much attention. This review introduces an effective technique in producing bulk ultrafine-grained (UFG) Mg alloys and promoting its hydrogen storage property, namely, equal-channel angular pressing (ECAP). This paper briefly describes the technical principle of ECAP and reviews the research progress on hydrogen storage properties of ECAP-processed Mg alloys. Special attention is given to their hydrogen storage behaviors including hydrogen storage dynamics, capacity, and cycling stability. Finally, it analyzes the factors that affect the hydrogen storage properties of ECAP-processed Mg alloys, such as the grain sizes, lattice defects, catalysts, and textures introduced by ECAP process.

This study systematically investigated the effects of biologically relevant microalloying elements—calcium (Ca), strontium (Sr), manganese (Mn), and zirconium (Zr)—on the electrochemical behavior of Mg-Y-Zn alloys containing long-period stacking ordered (LPSO) phases. The alloys were prepared by casting and characterized using X-ray diffraction (XRD), optical microscopy (OM), and scanning electron microscopy with energy-dispersive spectroscopy (SEM/EDS). Electrochemical properties were assessed through potentiodynamic polarization in Hank’s solution, and corrosion rates were determined by hydrogen evolution and weight loss methods. Microalloying significantly enhanced the corrosion resistance of the base Mg-Y-Zn alloy, with corrosion rates decreasing from 2.67 mm/year (unalloyed) to 1.65 mm/year (Ca), 1.36 mm/year (Sr), 1.18 mm/year (Zr), and 1.02 mm/year (Mn). Ca and Sr additions introduced Mg₂Ca and Mg₁₇Sr₂, while Mn and Zr refined the existing LPSO structure without new phases. Sr refined the LPSO phase and formed a uniformly distributed Mg₁₇Sr₂ network, promoting uniform corrosion and suppressing deep localized attacks. Ca-induced Mg₂Ca acted as a temporary sacrificial phase, with corrosion eventually propagating along LPSO interfaces. The Mn-containing alloy exhibited the lowest corrosion rate; this is attributed to the suppression of both anodic and cathodic reaction kinetics and the formation of a stable protective surface film. Zr improved general corrosion resistance but increased susceptibility to localized attacks due to dislocation-rich zones. These findings elucidate the corrosion mechanisms in LPSO-containing Mg alloys and offer an effective strategy to enhance the electrochemical stability of biodegradable Mg-based implants.

The computational fluid dynamics (CFD) simulation on the butte was carried out to obtain the wind field characteristics for a specific mountain in the hilly area of eastern China. Then, the speed-up ratios of butte at each location distributed by height were calculated. The simulation results were compared with the specified value of mountain wind field acceleration ratio in various codes. The finite element model of the transmission tower line system is established by ANSYS, and the wind-induced vibration response of the structural system under the single mountain wind field is calculated, which is compared with the results of flat ground. The results show that the mountain will hinder the fluid passing through it. There is a deceleration zone in front of the mountain and a flow separation phenomenon behind the mountain. The speed-up ratios at the butte top where accelerating effect are the biggest among all positions of the butte. As the height increases, they approach 1. The speed-up ratios calculated by the Chinese code and the Australian code are linearly changing along the ridge of the butte and are symmetric at the windward side and leeward side. The biggest speed-up ratios are calculated by the Chinese code, and the smallest ratios are calculated by CFD. The wind-induced vibration response of the transmission tower line system is influenced by the wind speed-up ratios and reaches the maximum at the top of the butte. The simulation results at the windward side are close to the values calculated by the Australia code and the Euro code, but at the top and leeward side, they are far smaller than others.

This study reveals the synergistic effects of Mn and Zr microalloying and equal-channel angular pressing (ECAP) on the microstructure and corrosion behavior of Mg-Y-Zn alloys in Hanks’ solution. At moderate deformation levels (four passes), the alignment of LPSO phases forms semi-continuous barrier structures, promoting the formation of dense corrosion product layers and improving corrosion resistance. (e.g., Mg-Y-Zn-Mn 4p: 1.07 mm·y⁻¹). However, excessive deformation (eight passes) leads to severe fragmentation of LPSO phases, increasing cathodic activity and intensifying micro-galvanic coupling in Mn-containing alloys (Mg-Y-Zn-Mn 8p: 2.61 mm·y⁻¹). In contrast, Zr-containing alloys exhibit continuous improvement in corrosion resistance with increasing ECAP passes, attributed to enhanced electrochemical uniformity resulting from homogeneous ultrafine-grained structures (Mg-Y-Zn-Zr 8p: 0.87 mm·y⁻¹). These findings elucidate the critical mechanism by which the interplay between microalloying chemistry and severe plastic deformation governs electrochemical uniformity and corrosion kinetics. This work provides new insight into the corrosion behavior of ECAP-processed Mg-Y-Zn alloys, highlighting the critical role of balancing microstructural refinement and electrochemical heterogeneity, and offers guidance for the optimization of corrosion-resistant Mg-based materials.