A drastically growing requirement of electronic packages with an increasing level of complexity poses newer challenges for the competitive manufacturing industry. Coupled with harsher operating conditions, these challenges affirm the need for encapsulated board-level (2nd level) packages. To reduce thermo-mechanical loads induced on the electronic components during operating cycles, a conformal type of encapsulation is gaining preference over conventional glob-tops or resin casting types. The availability of technology, the ease of automation, and the uncomplicated storage of raw material intensifies the implementation of thermoset injection molding for the encapsulation process of board-level packages. Reliability case studies of such encapsulated electronic components as a part of board-level packages become, thereupon, necessary. This paper presents the reliability study of exemplary electronic components, surface-mounted on printed circuit boards (PCBs), encapsulated by the means of thermoset injection molding, and subjected to cyclic thermal loading. The characteristic lifetime of the electronic components is statistically calculated after assessing the probability plots and presented consequently. A few points of conclusion are summarized, and the future scope is discussed at the end.
Light-emitting diodes (LEDs) have increasingly replaced conventional lamps in the fields of general lighting and consumer electronics. In addition to the sharp price fall, this is also due to the significantly higher energy efficiency and the smaller, more compact design. Recently, their robustness and reliability have also reached a level of quality that surpasses the characteristics of conventional light sources such as halogen and fluorescent lamps. Characteristics, such as excellent design freedom and the possibility for functional integration, highlight the main qualities of molded interconnect devices (MIDs). The use of this technology does not only open doors to extend the application field of LEDs to new products but also presents challenges to the lighting industry. There are many studies dealing with the reliability of LEDs as well as with the usability of the MID technology in different fields. But, the lack of experience from the manufacturers regarding the behavior of this interesting configuration (LED/MID) over the entire life cycle prevents this technology from establishing and consolidating its existence. As LEDs in the automotive sector, especially within headlamps, assume increasingly powerful lighting tasks and are no longer used exclusively for signal transfer or for displays, thermal properties of the substrate materials and the thermo-mechanical behavior of the assembly are particularly relevant. In this context, this paper presents a deep and detailed reliability investigation of this system (LED/MID) and examines the influence of the MID substrate choice on the long-term performance of the LED. The impact of the forward current and of the ambient temperature on the junction temperature of the LED is a proven fact. Therefore, the MID effect was inspected under different operating conditions based on infrared thermography. After analyzing the occurred failure mechanisms, by means of X-ray analysis, thermal transient testing and microscopy, the resulting lifetime model is also presented and discussed.
Due to many advantages, such as cost-effective production, design freedom and weight reduction, plastics have replaced metals and ceramics in many fields. However, engineering plastics are good thermal insulators. This characteristic, although beneficial in certain applications, poses many challenges in many heat generating applications. This can lead to hot spots or even to an increase of the device temperature. Along with the increasing demand for plastics in areas of the lighting technology or in the automotive field due to the free shaping potential, the requirements are becoming more challenging. Driven by the trend of miniaturization, applications with high heat generation often have to operate in the tightest of spaces. Since not always sufficient space for complex cooling systems is given, the housing or the substrate should assume the task of thermal management. In regard to this fact, the use of thermally conductive thermoplastics seems to be very appealing. Quality loss, poorer reliability, loss of performance and even failure can occur in case of insufficient heat dissipation. In order to improve the properties of these polymers, highly heat-conducting fillers are added in order to improve the thermal conductivity of the compound. Another technology trend that has been prevalent for years is the use of simulations. Due to shorter product life cycles and therefore shorter development times, simulation has become an indispensable part of the chain of product development. Time-consuming and costly test series make simulation more and more important as a tool for material and product design. In this context, this paper presents a novel approach for reliability investigation and lifetime estimation, based on simulation. Therefore, a simulative method based on coupling the results from the process simulation (injection molding simulation) to finite element analysis was developed and explained. This coupled method makes it possible to take into account the manufacturing process and its engendered filler orientation. The obtained findings are compared to conventional thermal steady-state analysis and used in order to better predict the lifetime of LEDs mounted on thermoplastic substrates, the so-called molded interconnect devices. It is demonstrated that it is necessary to consider the filler orientation, especially in case of 3D substrates.
Molded Interconnect Device (MID) Technology features excellent design freedom and great potential for functional integration for applications in indoor lighting. Spatial arrangement of LEDs and intelligent control elements enable highly efficient, situation aware lighting concepts with attractive design. Even more than in PCB based LED lighting technologies, there are significant degrees of freedom for improved thermal management when designing and manufacturing an MID. In this work, measures suitable for thermal management of MID for lighting applications manufactured with LPKF-LDS technology are identified and compared. Focus is on design for thermal management and application of recently developed high thermal conductivity polymers. To compare the effects of the different measures, simulations are performed with a range of combinations of individual measures for thermal management. The simulation results of the individual combinations are evaluated using design of experiments statistical methods. Low cost measures relying on design for thermal management are compared to measures implying higher manufacturing costs and to substrates manufactured from high thermal conductivity polymer compounds.
Due to the functional integration potential and the excellent design freedom, molded interconnect devices (MID) are becoming more and more attractive for several fields, such as consumer electronics, automotive and lighting technologies. In this context, the need for better reliability, especially for the solid state lighting, has significantly increased recently. Thermal management impacts not only the efficiency but also the reliability and the color stability of LED arrays, where LEDs are subjected to mutual interferences. Thus, the use of highly filled and thermally conductive thermoplastics appears very appealing.In light of this fact, an experimental and computational study, with focus on the influence of the substrate material and heat dissipation concepts on the thermal management of low- and high-power LEDs on MID, is presented in this paper. The accuracy of the implemented Finite Elements Analysis (FEA) is also examined in this work and used to forecast the reliability of a 3D-MID lighting module.
An ever-growing market demand for board (second) level packages (e.g., embedded systems, system-on-a-chip, etc.) poses newer challenges for its manufacturing industry in terms of competitive pricing, higher reliability, and overall dimensions. Such packages are encapsulated for various reasons including thermal management, protection from environmental conditions and dust particles, and enhancing the mechanical stability. In the due course of reducing overall sizes and material saving, an encapsulation as thin as possible imposes its own significance. Such a thin-walled conformal encapsulation serves as an added advantage by reducing the thermo-mechanical stresses occurring due to thermal-cyclic loading, compared to block-sized or thicker encapsulations. This paper assesses the encapsulation process of a board-level package by means of thermoset injection molding. Various aspects reviewed in this paper include the conception of a demonstrator, investigation of the flow simulation of the injection molding process, execution of molding trials with different encapsulation thicknesses, and characterization of the packages. The process shows a high dependence on the substrate properties, injection molding process parameters, device mounting tolerances, and device geometry tolerances. Nevertheless, the thermoset injection molding process is suitable for the encapsulation of board-level packages limiting itself only with respect to the thickness of the encapsulation material, which depends on other external aforementioned factors.