Marek Szostak

Prof. Marek Szostak

Poznan University of Technology
orcid

Research Focus & Metrics

Academic Career Length

44Years (1983-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 January 2023 in Materials
Verified
Journal Article
Open access
PDF file
DDDamian Dziadowiec
Damian Dziadowiec
Danuta MatykiewiczDanuta Matykiewicz
Danuta Matykiewicz
Marek SzostakMarek Szostak
Marek Szostak
Jacek AndrzejewskiJacek Andrzejewski
Jacek Andrzejewski
The review article presents the technology of producing polyolefin-based films by extrusion casting. Due to the wide use of this type of film as packaging for food and other goods, obtaining films with favorable properties is still a challenge for many groups of producers in the plastics market. The feedblock process and multimanifold process are the main methods of producing multi-layer film. In the case of food films, appropriate barrier properties are required, as well as durability and puncture resistance also at low temperatures. On the other hand, in order to properly pack and present products, an appropriate degree of transparency must be maintained. Therefore, processing aids such as anti-slip, anti-block and release agents are commonly used. Other popular modifiers, such as waxes, fatty acid amides and mineral fillers—silica, talc or calcium carbonate–and their use in film extrusion are discussed. The article also presents common production problems and their prevention.

1 April 2019 in Composites Part B: Engineering
Verified
Journal Article
Closed access
Jacek AndrzejewskiJacek Andrzejewski
Jacek Andrzejewski
Marek SzostakMarek Szostak
Marek Szostak
MBMateusz Barczewski
Mateusz Barczewski
PŁPatrycja Łuczak
Patrycja Łuczak

26 April 2020 in Polymers
Verified
Journal Article
Open access
PDF file
Aleksander HejnaAleksander Hejna
Aleksander Hejna
Mateusz BarczewskiMateusz Barczewski
Mateusz Barczewski
Jacek AndrzejewskiJacek Andrzejewski
Jacek Andrzejewski
Paulina KosmelaPaulina Kosmela
Paulina Kosmela
Adam PiaseckiAdam Piasecki
Adam Piasecki
TKTairong Kuang
Tairong Kuang
Application of lignocellulosic fillers in the manufacturing of wood polymer composites (WPCs) is a very popular trend of research, however it is still rarely observed in the case of rotational molding. The present study aimed to analyze the impact of wheat bran content (from 2.5 wt.% to 20 wt.%) on the performance of rotationally-molded composites based on a linear low-density polyethylene (LLDPE) matrix. Microscopic structure (scanning electron microscopy), as well as physico-mechanical (density, porosity, tensile performance, hardness, rebound resilience, dynamic mechanical analysis), rheological (oscillatory rheometry) and thermo-mechanical (Vicat softening temperature) properties of composites were investigated. Incorporation of 2.5 wt.% and 5 wt.% of wheat bran did not cause significant deterioration of the mechanical performance of the material, despite the presence of ‘pin-holes’ at the surface. Values of tensile strength and rebound resilience were maintained at a very similar level, while hardness was slightly decreased, which was associated with the porosity of the structure. Higher loadings resulted in the deterioration of mechanical performance, which was also expressed by the noticeable rise of the adhesion factor. For lower loadings of filler did not affect the rheological properties. However, composites with 10wt.% and 20 wt.% also showed behavior suitable for rotational molding. The presented results indicate that the manufacturing of thin-walled products based on wood polymer composites via rotational molding should be considered a very interesting direction of research.

1 December 2020 in Composites Part B: Engineering
Verified
Journal Article
Closed access
JAJacek Andrzejewski
Jacek Andrzejewski
AKAnna Krawczak
Anna Krawczak
KWKarolina Wesoły
Karolina Wesoły
Marek SzostakMarek Szostak
Marek Szostak

14 November 2019 in Polymers
Verified
Journal Article
Open access
PDF file
Jacek AndrzejewskiJacek Andrzejewski
Jacek Andrzejewski
MBMateusz Barczewski
Mateusz Barczewski
Marek SzostakMarek Szostak
Marek Szostak
The study presents a comparative analysis for two types of polymer fillers used during the processing of polypropylene by the injection molding technique. The aim of the study was to assess the usefulness of buckwheat husk waste as an alternative to the widely used wood fiber fillers. For this purpose, we prepared composite samples containing 10, 30 and 50 wt % of the filler, which were subjected to mechanical tests, thermal analysis, and structural observations in order to evaluate and compare their properties. Additionally, we evaluated the effectiveness of the composite system’s compatibility by using maleic anhydride grafted polypropylene (PP-g-MA). The results of mechanical tests confirmed a more effective reinforcement mechanism for wood fibers; however, with the addition of PP-g-MA compatibilizer, these differences were significantly reduced: we observed a 14% drop for tensile modulus and 5% for strength. This suggests high susceptibility to this type of adhesion promoter, also confirmed by SEM observations. The paper also discusses rheological measurements conducted on a rotational rheometer, which allowed to confirm more favorable flow characteristics for composites based on buckwheat husks.