Mario Radschun

Dr. Mario Radschun

Institute of Measuring and Sensor Technology, Ruhr West University of Applied Sciences, Mülheim, North Rhine-Westphalia, Germany
orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 February 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
CCChristoph Clemens
Christoph Clemens
MRMario Radschun
Mario Radschun
AJAnnette Elisabeth Jobst
Annette Elisabeth Jobst
Jörg HimmelJörg Himmel
Jörg Himmel
Olfa KanounOlfa Kanoun
Olfa Kanoun
Measurement of soil parameters, such as moisture, density and density change, can provide important information for evaluating the stability of earthwork structures and for structural health monitoring. To ensure the stability of flood protection dikes, erosion at the contact zones of different soil zones must be avoided. In this work we propose the use of impedance spectroscopy to measure changes in density and volume caused by contact erosion. Erosion leads generally to a volume decrease in the contact zones between soils with different grain sizes and, consequently, to cavities in the dike structure. For this purpose, a proctor mould was developed for emulating contact erosion and the realisation of impedance measurements. Experimental investigations show a correlation between volume change of the soils in the proctor mould and impedance value. For a volume change of soil in the range of approximately 1.5% to 5.3%, an impedance change arises in the range of 17.2% to 29.8%. With several investigations we proof, that it is possible to detect material transport by impedance spectroscopy.

22 July 2022 in Sensors
Verified
Journal Article
Open access
PDF file
CCChristoph Clemens
Christoph Clemens
AJAnnette Elisabeth Jobst
Annette Elisabeth Jobst
MRMario Radschun
Mario Radschun
Jörg HimmelJörg Himmel
Jörg Himmel
Olfa KanounOlfa Kanoun
Olfa Kanoun
MQMarkus Quirmbach
Markus Quirmbach
Measuring weather data in an urban environment is an important task on the journey towards smart cities. Heavy rain can cause flooding in cities and prevent emergency services from reaching their destination because roads or underpasses are blocked. In order to provide a high-resolution site-specific overview in urban areas during heavy rainfall, a dense measurement network is necessary. To achieve this, a smart low-cost rain gauge is needed. In this paper, the current status of the development of an inductive rain gauge is presented. The sensor is based on the eddy current principle and evaluates the frequency of an electrical resonant circuit. For this purpose, a coil is placed under a metal plate. When raindrops hit the plate, it starts to oscillate, which changes the distance to the coil accordingly and causes changes in the frequency of the resonant circuit. Since the sensor is cost-effective, operates self-sufficiently in terms of energy and transmits data wirelessly via LoRaWAN, it can be used flexibly. This enables dense, area-wide coverage over the urban area of interest. The first experimental investigations show a correlation between the size of the rain droplets and the frequency change. Small droplets cause a shift of about 8 kHz and larger droplets of up to 40 kHz. The results prove that raindrops can be detected and categorized using this measurement principle. These data will be used as a basis for future work on calculating precipitation.

1 March 2017
Verified
Conference Paper
Closed access
MRMario Radschun
Mario Radschun
TMTino Morgenstern
Tino Morgenstern
RSRene Schafer
Rene Schafer
OKOlfa Kanoun
Olfa Kanoun
JHJorg Himmel
Jorg Himmel
The detection of soil erosion processes in dams, hydraulic heave failure or corrosion processes of reinforcing steel in concrete are a small selection of measuring applications in civil engineering where the impedance analysis can be used to determine the measurand. Those measuring applications are having high requirements for the measuring hardware. For example a common interface for fast data exchange, high resolution, independent functionality and easy customizability to suit the measuring application. For that reason, a well-known application for steel-mill process monitoring can be used as a development platform. This hardware platform is based on a vector network analyzer and is meeting the requirements mainly. However, a couple of modifications has to be made, like replacing the ADC for a higher sample rate, Ethernet for easy and fast data exchange and the microcontroller for more calculation power.

27 September 2023 in Measurement
Verified
Journal Article
Closed access
MRMario Radschun
Mario Radschun
CCChristoph Clemens
Christoph Clemens
AJAnnette Elisabeth Jobst
Annette Elisabeth Jobst
AHAndreas Hennig
Andreas Hennig
JHJörg Himmel
Jörg Himmel
OKOlfa Kanoun
Olfa Kanoun

16 April 2024 in Measurement
Verified
Journal Article
Open access
MRMario Radschun
Mario Radschun
AJAnnette Elisabeth Jobst
Annette Elisabeth Jobst
CCChristoph Clemens
Christoph Clemens
JHJörg Himmel
Jörg Himmel
AHAndreas Hennig
Andreas Hennig
OKOlfa Kanoun
Olfa Kanoun

28 January 2020 in TM - Technisches Messen
Verified
Journal Article
Closed access
PDF file
MRMario Radschun
Mario Radschun
AJAnnette Elisabeth Jobst
Annette Elisabeth Jobst
Jörg HimmelJörg Himmel
Jörg Himmel
Olfa KanounOlfa Kanoun
Olfa Kanoun
The development of innovative measuring technology for process optimization in hot rolling mills becomes more and more relevant because of increasing demands on product quality. Measurement technology for high-resolution non-contact cross-sectional area measurement has shown that the variation in cross-sectional area contains information about the rolling process. This information can be used for the development of new measurement devices and analytical methods for process optimization. The harsh environmental conditions and strict safety regulations result in great effort when implementing a new sensor prototype in hot rolling mills. For this reason, this work presents a mechatronic test stand that can simulate the cross-sectional area variation under laboratory conditions realistically.