A concurrent-hybrid non-dominated sorting genetic algorithm (hybrid NSGA-II) has been developed and applied to the simultaneous optimization of the annual energy production, flapwise root-bending moment and mass of the NREL 5 MW wind-turbine blade. By hybridizing a multi-objective evolutionary algorithm (MOEA) with gradient-based local search, it is believed that the optimal set of blade designs could be achieved in lower computational cost than for a conventional MOEA. To measure the convergence between the hybrid and non-hybrid NSGA-II on a wind-turbine blade optimization problem, a computationally intensive case was performed using the non-hybrid NSGA-II. From this particular case, a three-dimensional surface representing the optimal trade-off between the annual energy production, flapwise root-bending moment and blade mass was achieved. The inclusion of local gradients in the blade optimization, however, shows no improvement in the convergence for this three-objective problem.
This paper describes a computer method to allow the design of small wind turbine blades for the multiple objectives of rapid starting, efficient power extraction, low noise, and minimal mass. For the sake of brevity, only the first two and the last objectives are considered in this paper. The optimization aimed to study a range of blade materials, from traditional fibreglass through sustainable alternatives to rapid prototyping plastic. Because starting performance depends on blade inertia, there is a complex interaction between the material properties and the aerodynamics. Example blades of 1.1 m length were designed to match a permanent magnet generator with a rated power of 750 W at 550 rpm. The materials considered were (a) traditional E-glass and polyester resin; (b) flax and polyester resin; (c) a typical rapid prototyping plastic, ABS-M30; and (d) timber. Except for (d), hollow blades were used to reduce the rotor inertia to help minimize starting time. Two airfoils are considered: the 10% thick SG6043 which has excellent lift:drag performance at low Reynolds number and the SD7062 whose extra thickness (14%) has some structural advantages, particularly for the weaker material (c). All blade materials gave feasible designs with material (d) the only one that required a blade shell thickness greater than the specified minimum value of 1% of the blade chord. Generally, the blade chord and twist increased as starting was given greater importance. In all cases, the associated increase in blade inertia was outweighed by the larger aerodynamic torque. Materials (a), (b), and (d) were better suited to the SG6043 airfoil whereas ABS-M30 benefitted from the thicker SD7062 section.
This article describes Computational Fluid Dynamics (CFD) simulations of flows in a wind farm in complex terrain in Shaanxi, China and the comparisons of the computational results with utility scale field measurements. The CFD simulations performed in the study are using either a Reynolds-Averaged Navier–Stokes (RANS) or Large-Eddy Simulation (LES) solver. The RANS method together with an Actuator Disc (AD) approach is employed to predict the performance of the 25 wind turbines in the farm, while the LES and Actuator Line (AL) technique is used to obtain a detailed description of the flow field around a specific wind turbine #14 near two met masts. The AD-RANS simulation results are compared with the mean values of power obtained from field measurements. Furthermore, the AL-LES results are compared with the mean values of power, rotor speed, and wind speed measured from the wind turbine and its nearby two masts. Results from the simulations indicate that both AD-RANS and AL-LES methods can reasonably predict the performance of the wind farm and wind turbine #14, respectively, in complex terrain in Shaanxi. The mean percent difference obtained for power in the AD-RANS simulations was approximately 20%. Percent differences obtained for power and rotor RPM in the AL-LES varied between 0.08% and 11.6%. The mean percent differences in the AL-LES for power and rotor RPM are approximately 7% and 1%, respectively.
The manuscript presents a novel aero‐hydro‐servo‐elastic coupling framework, MIRAS‐HAWC2. In this coupling, the wind turbine blades and rotor‐wake aerodynamics are modeled using a modified lifting‐line theory which accounts for blade curvature, combined with a hybrid vortex method. The wind turbine structure and foundation are modeled using a finite‐element and multi‐body system approach. Last, hydrodynamics are modeled using Airy wave theory together with Morison's equation. An initial assessment of the performance of the aeroelastic coupling framework has been performed for steady rotor‐only cases, assuming laminar inflow without shear. This included a comparison against fully resolved computational fluid dynamics, for both stiff and flexible blades showing an excellent agreement. In a second stage, the aero‐hydro‐servo‐elastic coupling is used, comparing MIRAS‐HAWC2 as well as blade‐element momentum‐based simulations with selected results from the Offshore Code Comparison Collaboration projects (OC3 and OC4), which study the NREL 5 MW turbine mounted on different offshore support structures. A good agreement has been obtained for the simulations of a monopile with rigid foundation, a tripod, and jacket support structures.