In this study, the optimization of the parameters used in the engraving process of wooden birch plywood material with a CO2 laser machine was investigated using the Taguchi method. An industrial laser machine with a 150W glass tube was used during the experimental examination process. There are basic factors affecting the engraving process of wooden surfaces such as laser power (P), engraving speed (S) and laser head parts (F). The engraving depth (D) and engraving width formed on the surface during the engraving process are the main factors that determine the aesthetics of the product. Taguchi L25 orthogonal array was used in the experiments to determine and optimize the highly important parameters. The optimum combination of parameters in the laser engraving process was then evaluated. The research results showed that the effect of P and S factors played a leading role, and the F parameter had a small effect on the depth of wood scraping. Optimization results found that F:5, S:100 and P:30 gave the best engraving depth optimization, while F:6, S:300 and P:10 gave the lowest engraving depth optimization result.
Wood, as the oldest building material, provides some of the basic needs of human beings, including shelter and protection. Wood is used in exterior cladding, carrier systems, joinery, ceiling-floor coverings, windows, doors, and furniture production. When wooden material is exposed to external weather conditions, due to its hygroscopic structure, its physical and mechanical properties deteriorate from exposure to moisture, temperature, and biological organisms. The bending modulus of elasticity of Scots pine (Pinus sylvestris L.), oak (Quercus petraea L.), and chestnut (Castanea sativa M.) wood that was tannin-impregnated and heat-treated at 160 °C, was investigated using Taguchi L9 (33). The sequence was optimized. After heat treatment, the carrier elements were subjected to artificial climate conditions. In the optimization of the data obtained, it was understood that the highest impact factor was the tree type. In contrast, the climate on the elastic modulus was the lowest impact factor. In Taguchi analysis, a mathematical prediction model was created using actual and predicted data using the S/N ratio’s biggest-best equation. The R2 of the model can be predicted with an accuracy rate of 98.6%.
30 June 2022 in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
In this study, the behavior of tannin-modified and pre-heat treated wooden beams in different climatic conditions were determined. For this purpose; Samples prepared according to TS EN 386 standards from Scots pine (Pinus sylvestris L.), oak (Quercus petraea L.) and chestnut (Castanea sativa Mill.) woods were impregnated with acorn tannin and pre-heated for 2 hours at 150°C and 160°C. After the samples were conditioned at 20°C temperature and 65% RH, 40°C temperature and 35% RH, 10°C temperature and 50% RH, bending strength tests according to TS 2474 and modulus of elasticity in bending according to TS 2478 were applied. As a result; At the level of wood species-process type interaction, the highest increase in bending strength was determined as 7.6% in tannin modified scotch pine samples at 150ºC compared to the control samples. Accordingly, it can be suggested to use Scotch pine wood in the manufacture of lightly loaded wooden house columns and beams and other building elements.
16 January 2026 in European Journal of Wood and Wood Products
Ahşap malzemenin yoğun olarak kullanıldığı mobilya ve tasarım atölyelerinde, ağaç işleme makinaları fazla miktarda talaş ve toz üretmektedir. Bu talaş ve özellikle tozların doğrudan çalışma ortamı ile havaya bırakılması insan için sağlık sorunlarına yol açmaktadır. Bunun için geleneksel olarak makinalardan sürekli emiş yapan toz ve talaş toplama üniteleri kullanılmaktadır. Makinalara hortumlar ve borular ile bağlı olan bu sistemler sürekli tüm makinelerden emiş yapmaktadır. Bazı sistemlerde ise her makinenin emiş yapan kısmındaki klapa manuel olarak kapatılıp açılmaktadır. Bu şekilde çalışan sistemler hem enerji verimliliğini azaltmakta hem de makine başına düşen hava emiş miktarını azaltmaktadır. Bu çalışmada ana talaş toplama ünitesine bir hava emiş hattı kurulmuştur. Her bir makine emiş hattına konumlandırılmış klapalara bağlı servo motorlar ile Arduino Uno mikrodenetleyici ve üzerindeki IR alıcılar ile haberleşerek toz toplama ünitesini ve yalnızca çalışmakta olan makine hattından emiş yapılmasını sağlamaktadır. Sistem için özgün bir devre kartı tasarlanmış, bu kart kompakt olarak duvar prizlerinin içerisine yerleştirilmiştir. Bu sayede tasarlanan sistem herhangi bir tadilat gerektirmeden düşük maliyetli ve enerji verimliliği yüksek olup, mevcut atölyelerde bulunan toz toplama hatlarına entegre edilebilmektedir.