Mesut DEMİRBİLEK

Dr. Mesut DEMİRBİLEK

Mechanical Engineering, Ahi Evran University, Kırşehir, Turkey (Türkiye)
orcid
I am pursuing a doctorate.

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2024 in Applied Rheology
Verified
Journal Article
Open access
PDF file
MDMerdin Danışmaz
Merdin Danışmaz
Mesut DEMİRBİLEKMesut DEMİRBİLEK
Mesut DEMİRBİLEK
In this study, the thermo-flow behaviours of the spiral tube were examined using water and some nanofluids such as TiO2, Al2O3, Fe2O3, CuO, ZnO, and CeO2. The computational flow dynamic modelling of the spiral coiled tube was performed with ANSYS 20 software program. The k–ε model with a standard wall function was used to simulate the thermo-flow characteristics. The solution of the governing equations was performed using the discretization method of finite volume. The study was carried out considering the case of fluid-to-fluid heat transfer in turbulent conditions. The influence of different key design parameters such as Reynolds number, different nanofluids, and flow arrangements was of main interest. The volume concentration of the nanofluids is 1%. The experiments were performed at different Reynolds ranges (9,000, 14,000, 20,000, and 25,000). The outlet temperature values, heat transfer coefficient, coefficient of friction, Nusselt number values of water, and nanofluids were found and compared. It was found that the outlet temperature, heat transfer coefficient, and Nusselt number values of water were the lowest, while the coefficient of friction value was the highest compared to the nanofluids. Among the nanofluids, CeO was found to have the highest outlet temperature, heat transfer coefficient, and Nusselt number value, as well as the lowest coefficient of friction value. TiO2 was found to have the lowest outlet temperature (T out), the heat transfer coefficient value, and the highest coefficient of friction value. Al2O3 was found to have the lowest Nusselt number. In addition, Nusselt number values were obtained at different Dean numbers of water (2,200, 3,400, 4,900, 6,100, 7,350, and 8,600) and found to be compatible with previous studies. In addition, the coefficients of friction values of water at different velocities (0.18, 0.24, 0.41, 0.71, 0.95, 1.07, and 1.18) were obtained and found to be compatible with previous studies.

29 August 2026 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Mesut DEMİRBİLEKMesut DEMİRBİLEK
Mesut DEMİRBİLEK
MDMerdin Danışmaz
Merdin Danışmaz
This study numerically investigated thermal enhancement in helical tube flows equipped with an embedded wire/spring turbulator. Five turbulator configurations (circular, square, and two different rectangular cross-sections) were examined for turbulent operation using water and three nanofluids (CuO–water, TiO2–water, and Al2O3–water). The insertion of the turbulator reorganized the flow and intensified near-wall mixing, which led to consistently higher heat-transfer performance as evidenced by enhanced Nusselt number (Nu) levels. However, these thermal gains were accompanied by additional hydraulic losses, reflected in increased friction factor (f) and pressure-drop penalties. The results also revealed that Nu increases with increasing Dean number, indicating that curvature-driven secondary motions and turbulence augmentation act synergistically in promoting convection. In contrast, the hydrodynamic cost intensifies with flow strength, producing a net decrease in thermal efficiency, η, with Reynolds number for all cases. This decline occurs because the pressure-drop growth rate exceeds the incremental heat-transfer improvement. Among the examined fluids, nanofluids generally provided higher η than water, while Al2O3–water exhibited the most favorable behavior among the nanofluids. To jointly account for thermal and hydraulic effects, the thermal performance factor (TPF) was evaluated and found to decrease with Reynolds number across all fluids, implying that heat-transfer benefits become less dominant at higher inertia. The combined results highlight that selecting the appropriate turbulator cross-section and working fluid is essential for achieving an efficient thermal–hydraulic equilibrium.