Nano-zero-valent iron biochar derived from almond shell (nZVI-ASBC) was used for hexavalent chromium (CR) removal. Experiments showed that pH was the main factor (p < 0.01) that affected the experimental results. At a dosage of 10 mg·L−1 and pH of 2–6, in the first 60 min, nZVI-ASBC exhibited a removal efficiency of 99.8%, which was approximately 20% higher than the removal yield at pH 7–11. Fourier transform infrared spectroscopy results indicated N-H was the main functional group that influenced the chemisorption process. The pseudo second-order dynamics and Langmuir isotherm models proved to be the most suitable. Thermodynamic studies showed that the reaction was exothermic and spontaneous at low temperatures (T < 317 K). Various interaction mechanisms, including adsorption and reduction, were adopted for the removal of Cr(VI) using the nZVI-ASBC composite. The findings showed that the BC-modified nZVI prepared with almond shell exerts a good effect and could be used for the removal of Cr(VI).
Ex situ catalytic pyrolysis of biomass using char-supported nanoparticles metals (Fe and Ni) catalyst for syngas production and tar decomposition was investigated. The characterizations of fresh Fe-Ni/char catalysts were determined by TGA, SEM–EDS, Brunauer–Emmett–Teller (BET), and XPS. The results indicated that nanoparticles metal substances (Fe and Ni) successfully impregnated into the char support and increased the thermal stability of Fe-Ni/char. Fe-Ni/char catalyst exhibited relatively superior catalytic performance, where the syngas yield and the molar ratio of H2/CO were 0.91 Nm3/kg biomass and 1.64, respectively. Moreover, the lowest tar yield (43.21 g/kg biomass) and the highest tar catalytic conversion efficiency (84.97 wt.%) were also obtained under the condition of Ni/char. Ultimate analysis and GC–MS were employed to analyze the characterization of tar, and the results indicated that the percentage of aromatic hydrocarbons appreciably increased with the significantly decrease in oxygenated compounds and nitrogenous compounds, especially in Fe-Ni/char catalyst, when compared with no catalyst pyrolysis. After catalytic pyrolysis, XPS was employed to investigate the surface valence states of the characteristic elements in the catalysts. The results indicated that the metallic oxides (MexOy) were reduced to metallic Me0 as active sites for tar catalytic pyrolysis. The main reactions pathway involved during ex situ catalytic pyrolysis of biomass based on char-supported catalyst was proposed. These findings indicate that char has the potential to be used as an efficient and low-cost catalyst toward biomass pyrolysis for syngas production and tar decomposition.
CO2 catalytic conversion to CO would likely be an important part of CO2 mitigation and utilization. In this work, CuAl2O4 was developed with a spinel structure that acts as an active and stable catalyst for this reaction. Here, the fundamental characteristics of CuAl2O4 catalyst were studied to understand the catalytic mechanism for the Reverse Water Gas Shift reaction. Based on the catalytic mechanism, the CuAl2O4 catalyst was found to have exceptional catalytic activity due to the high dispersion of copper on its surface, and it could have higher catalytic activity by increasing the oxygen vacancies on the surface of the catalyst via alkalinization treatment. By combining with XPS spectra, the relationship between the Raman mode and the oxygen vacancy structure on the CuAl2O4 surface was proved. Through these studies, it was proved that alkalinization treatment can regulate the oxygen vacancies on the surface of the catalyst and thus enhance the catalytic activity.
Understanding the solubility of CO2 is critical for implementing CO2-enhanced oil recovery (CO2-EOR). In this work, the solubility of CO2 in n-decane in a temperature range between 303.15 K and 353.15 K and pressures up to 15 MPa was measured using a fused silica capillary cell with in situ Raman spectroscopy. A semi-empirical CO2 solubility prediction model was obtained according to the experimental results. In order to improve the solubility of CO2 in n-decane, the solubility of CO2 in n-decane and co-solvent n-hexane (3% wt) mixture was also comparatively investigated. The results indicated that the solubility of CO2 in n-decane was 1.6355~64.0084 mol/kg. The data from the prediction model were in good agreement with the experimental data, and the mean relative deviation was 3.65%, indicating that the prediction model could be used to predict the solubility of CO2 in n-decane under different conditions. The solubility of CO2 in n-decane + n-hexane system ranged from 1.0127 mol/kg to 65.7286 mol/kg. It was found that, under low-pressure conditions, the addition of co-solvent n-hexane did not enhance the solubility of CO2, while it had a certain enhancement effect on the dissolution of CO2 under high-pressure conditions. As the temperature increased from 303.15 K to 353.15 K, the enhancement efficiency of the solubility of CO2 also increased from 1.34~2.05% to 8.17~9.82%, and the average enhancement efficiency increased from 1.74% to 9.00%. This study provides more CO2 solubility data for CO2-EOR.
Magnetic Zn0.25Mn0.75Fe2O4 was applied to the degradation of azoxystrobin in a Fenton-like system, and the performance was enhanced via crystal structure control.