A biowaiver is accepted by the Brazilian Health Surveillance Agency (ANVISA) for immediate-release solid oral products containing Biopharmaceutics Classification System (BCS) class I drugs showing rapid drug dissolution. This study aimed to simulate plasma concentrations of fluconazole capsules with different dissolution profiles and run population simulation to evaluate their bioequivalence. The dissolution profiles of two batches of the reference product Zoltec^® 150 mg capsules, A1 and A2, and two batches of other products (B1 and B2; C1 and C2), as well as plasma concentration–time data of the reference product from the literature, were used for the simulations. Although products C1 and C2 had drug dissolutions < 85% in 30 min at 0.1 M HCl, simulation results demonstrated that these products would show the same in vivo performance as products A1, A2, B1, and B2. Population simulation results of the ln-transformed 90% confidence interval for the ratio of C_max and AUC_0–t values for all products were within the 80–125% interval, showing to be bioequivalent. Thus, even though the in vitro dissolution behavior of products C1 and C2 was not equivalent to a rapid dissolution profile, the computer simulations proved to be an important tool to show the possibility of bioequivalence for these products.

The development of extended-release dosage forms with adequate drug release is a challenge for pharmaceutical companies, mainly when the drug presents high solubility, as in Biopharmaceutics Classification System (BCS) class I. This study aimed to develop extended-release mini-tablets containing metoprolol succinate (MS), while integrating design of experiments (DOE) and physiologically based biopharmaceutics modeling (PBBM), to predict its absorption and to run virtual bioequivalence (VBE) studies in both fasted and fed states. Core mini-tablet formulations (F1, F2, and F3) were prepared by direct compression and coated using nine coating formulations planned using DOE, while varying the percentages of the controlled-release and the pore-forming polymers. The coated mini-tablets were submitted to a dissolution test; additional formulations were prepared that were optimized by simulating the dissolution profiles, and the best one was submitted to VBE studies using GastroPlus^® software. An optimized formulation (FO) containing a mixture of immediate and extended-release mini-tablets showed to be bioequivalent to the reference drug product containing MS when running VBE studies in both fasted and fed states. The integration of DOE and PBBM showed to be an interesting approach in the development of extended-release mini-tablet formulation containing MS, and can be used to rationalize the development of dosage forms.

D-limonene, derived from citrus essential oils, holds significant therapeutic potential but faces challenges due to its high volatility, especially in pharmaceutical formulations. This study investigates microemulsions as a promising delivery system for volatile compounds, emphasizing their thermal protection for D-limonene. The formulation development was guided by a pseudo-ternary phase diagram and involved assays with different surfactants. Microemulsions were achieved solely with Labrasol^® (Gattefossé Brasil, São Paulo, Brazil), encompassing concentrations of 7.1% to 30.8% D-limonene, 28.6% to 57.1% Labrasol^®, and 20.0% to 64.3% water. All formulations were homogeneous, transparent, and presented low viscosity, with adequate D-limonene content, indicating that the production is feasible at room temperature. While the formulations demonstrated robust physical stability under mechanical stress, they exhibited destabilization at temperatures exceeding 50 °C. In terms of oxidative stability, pure D-limonene exhibited an induction period of 4.88 min, whereas microemulsions extended this period by four to eight times. Notably, the induction period of the microemulsions remained practically unchanged pre and post-heating (70 °C), suggesting the formulation’s ability to enhance the D-limonene thermal stability. This highlights the value of oxidative stability analysis as a quicker tool than conventional oxidative tests, while affirming microemulsions as a viable encapsulation strategy for D-limonene protection against elevated temperatures.

This study aimed to develop a biopredictive dissolution method for desvenlafaxine ER tablets using design of experiments (DoE) and physiologically based biopharmaceutics modeling (PBBM) to address the challenge of developing generic drug products by reducing the risk of product failure in pivotal bioequivalence studies. For this purpose, a PBBM was developed in GastroPlus^® and combined with a Taguchi L9 design, to evaluate the impact of different drug products (Reference, Generic #1 and Generic #2) and dissolution test conditions on desvenlafaxine release. The influence of the superficial area/volume ratio (SA/V) of the tablets was observed, mainly for Generic #1, which presented higher SA/V than the others, and a high amount of drug dissolved under similar test conditions. The dissolution test conditions of 900 mL of 0.9% NaCl and paddle at 50 rpm with sinker showed to be biopredictive, as it was possible to demonstrate virtual bioequivalence for all products, despite their release-pattern differences, including Generic #3 as an external validation. This approach led to a rational development of a biopredictive dissolution method for desvenlafaxine ER tablets, providing knowledge that may help the process of drug product and dissolution method development.

The search for new pharmaceutical dosage forms and different drug delivery systems already used in therapeutics is a global trend, serving as an opportunity to expand the portfolio for the pharmaceutical industry. In this context, multiparticulate systems, such as pellets, granules, and minitablets, represent an attractive alternative, given the range of possibilities they provide. Among the methods used in the production of these systems, we highlight the process of extrusion-spheronization for pellet manufacture, wet granulation and hot-melt extrusion for the obtention of granules, and direct compression for minitablets. Although highly versatile, depending on the technology chosen, many processes and formulation variables can influence the ensuing stages of manufacture, as well as the final product. Therefore, the characterization of these small units is of fundamental importance for achieving batch homogeneity and optimal product performance. Analyses, including particle size distribution, morphology, density, porosity, mechanical strength and disintegration, are example tests used in this characterization. The objective of this review was to address the most widely used tests for the physical evaluation of multiparticulate systems.