The wireless power transfer via an electro-magnetic (EM) wave enables far-field power transfer for supplying power to IoT devices. However, the power attenuation of the EM wave leads to low end-to-end power transfer efficiency. In this paper, we provide an analytic and experimental study on the distributed wireless power transfer system as a means to overcome the low power transfer efficiency. In the distributed wireless power transfer system, a number of multi-antenna power beacons, which are distributed over space, send out wireless power to charge IoT devices. Since each power beacon has a separate local oscillator and controller, it is very challenging to achieve frequency and phase synchronization among power beacons, which is the prerequisite for optimal distributed beamforming. In this paper, we study the performance of the distributed wireless power transfer system with or without the frequency and phase synchronization. Based on the experiment and simulation results, we show that the distributed wireless charging is advantageous in terms of the coverage probability as long as the optimal distributed beamforming is available in the distributed wireless power transfer system.
Recently, the fifth generation of cellular mobile communications (5G) network has been deployed and become pervasive. 5G offers a significant increase in terms of bandwidth and data rate compared to the previous generations. In addition, new technologies such as millimeter-wave (mmWave) technology and massive MIMO (mMIMO), have been proposed to meet the demand. However, some inevitable challenges still exist. In mmWave frequency, path loss and shadowing become more severe due to the radio electromagnetic (EM) wave characteristics. In this paper, we propose the utilization of reconfigurable intelligent surface (RIS) to aid wireless communications to overcome path loss and shadowing issues, by using a compressive sensing-based adaptive beamforming algorithm. To validate the theory, hypothesis, and simulation results, we have designed, fabricated, and conducted experiments with a 1-bit RIS testbed. The results show that the bit error rate (BER) and signal-to-noise ratio (SNR) of the received signal are significantly improved when the proposed RIS is employed. Further, we have also demonstrated a video streaming application aided by the proposed RIS as one of the potential RIS deployment scenarios.
Wireless information and energy transfer (WIET) represents an emerging paradigm that employs controllable transmission of radio frequency signals for the dual purpose of data communication and wireless charging. As such, WIET is widely regarded as an enabler of envisioned sixth-generation (6G) use cases that rely on energy-sustainable Internet-of-Things (IoT) networks, such as smart cities and smart grids. Meeting the quality-of-service demands of WIET, in terms of both data transfer and power delivery, requires effective codesign of the information and energy signals. In this article, we present the main principles and design aspects of WIET, focusing on its integration in 6G networks. First, we discuss how conventional communication notions, such as resource allocation and waveform design, need to be revisited in the context of WIET. Next, we consider various candidate 6G technologies that can boost WIET efficiency, namely, holographic multiple-input multiple-output, near-field beamforming, terahertz communication, intelligent reflecting surfaces (IRSs), and reconfigurable (fluid) antenna arrays. We introduce respective WIET design methods, analyze the promising performance gains of these WIET systems, and discuss challenges, open issues, and future research directions. Finally, a near-field energy beamforming scheme and a power-based IRS beamforming algorithm are experimentally validated using a wireless energy transfer testbed. The vision of WIET in communication systems has been gaining momentum in recent years, with constant progress with respect to theoretical and also practical aspects. The comprehensive overview of the state of the art of WIET presented in this article highlights the potential of WIET systems and their overall benefits in 6G networks.
Reconfigurable intelligent surface (RIS) is a promising technology for radio-frequency wireless power transfer (WPT) as it is capable of beamforming and beam focusing without using active and power-hungry components. In this article, we propose a multitile RIS beam scanning (MTBS) algorithm for powering up Internet of Things (IoT) devices. Considering the hardware limitations of the IoT devices, the proposed algorithm requires only power information to enable the beam focusing capability of the RIS. Specifically, we first divide the RIS into smaller RIS tiles. Then, all RIS tiles and the phased array transmitter are iteratively scanned and optimized to maximize the receive power. We elaborately analyze the proposed algorithm and build a simulator to verify it. Furthermore, we have built a real-life testbed of RIS-aided WPT systems to validate the algorithm. The experimental results show that the proposed MTBS algorithm can properly control the transmission phase of the transmitter and the reflection phase of the RIS to focus the power at the receiver. Consequently, after executing the algorithm, about 20-dB improvement of the receive power is achieved compared to the case that all unit cells of the RIS are in OFF state. By experiments, we confirm that the RIS with the MTBS algorithm can greatly enhance the power transfer efficiency.
We propose and implement a novel 1-bit coding metasurface that is capable of focusing and steering beam for enhancing power transfer efficiency of the electromagnetic (EM) wave-based wireless power transfer systems. The proposed metasurface comprises 16 × 16 unit cells which are designed with a fractal structure and the operating frequency of 5.8 GHz. One PIN diode is incorporated within each unit cell and enables two states with phase change of the reflected signal at the unit cell. The two states of the unit cell correspond to the ON and OFF states of the PIN diode or “0” and “1” coding in the metasurface. By appropriately handling the ON/OFF states of the coding metasurface, we can control the reflected EM wave impinged on the metasurface. To verify the working ability of the coding metasurface, a prototype metasurface with a control board has been fabricated and measured. The results showed that the coding metasurface is capable of focusing beam to desired direction. For practical scenarios, we propose an adaptive optimal phase control scheme for focusing the beam to a mobile target. Furthermore, we prove that the proposed adaptive optimal phase control scheme outperforms the random phase control and beam synthesis schemes.
In this paper, we present a 5.8 GHz radio-frequency (RF) wireless power transfer (WPT) system that consists of 64 transmit antennas and 16 receive antennas. Unlike the inductive or resonant coupling-based near-field WPT, RF WPT has a great advantage in powering low-power internet of things (IoT) devices with its capability of long-range wireless power transfer. We also propose a beam scanning algorithm that can effectively transfer the power no matter whether the receiver is located in the radiative near-field zone or far-field zone. The proposed beam scanning algorithm is verified with a real-life WPT testbed implemented by ourselves. By experiments, we confirm that the implemented 5.8 GHz RF WPT system is able to transfer 3.67 mW at a distance of 25 meters with the proposed beam scanning algorithm. Moreover, with the proposed beam scanning algorithm, the power transfer efficiency reaches 20.32 % and 0.24 % at distances of 0.5 and 5 meters, respectively, whereas the far-field-only-scanning scheme achieved the transfer efficiencies of 13.45 % and 0.23 % at the same receiver positions. Since the proposed transmit antenna array has the maximum linear dimension of 299.12 mm, the approximate boundary between far-field and radiative near-field is 3.45 meters based on the Fraunhofer distance calculation. The results show that the proposed algorithm can effectively cover radiative near-field region differently from the conventional scanning schemes which are designed under the assumption of the far-field WPT.