Mohammad Rezwan Khan

Dr. Mohammad Rezwan Khan

Akka Technologies (France), Paris, Île-de-France, France
orcid
Doctorate in Engineering

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 August 2014 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
FDFujin Deng
Fujin Deng
Zhe ChenZhe Chen
Zhe Chen
Mohammad Rezwan KhanMohammad Rezwan Khan
Mohammad Rezwan Khan
RZRongwu Zhu
Rongwu Zhu
The modular multilevel converter (MMC) is attractive for medium- or high-power applications because of the advantages of its high modularity, availability, and high power quality. However, reliability is one of the most important issues for MMCs which are made of large number of power electronic submodules (SMs). This paper proposed an effective fault detection and localization method for MMCs. An MMC fault can be detected by comparing the measured state variables and the estimated state variables with a Kalman filter. The fault localization is based on the failure characteristics of the SM in the MMC. The proposed method can be implemented with less computational intensity and complexity, even in case that multiple SM faults occur in a short time interval. The proposed method is not only implemented in simulations with professional tool PSCAD/EMTDC, but also verified with a down-scale MMC prototype controlled by a real-time digital signal controller in the laboratory. The results confirm the effectiveness of the proposed method.

16 March 2017 in Batteries
Verified
Journal Article
Open access
PDF file
Mohammad Rezwan KhanMohammad Rezwan Khan
Mohammad Rezwan Khan
MSMaciej Swierczynski
Maciej Swierczynski
SKSoren Knudsen Kaer
Soren Knudsen Kaer
The prevailing standards and scientific literature offer a wide range of options for the construction of a battery thermal management system (BTMS). The design of an innovative yet well-functioning BTMS requires strict supervision, quality audit and continuous improvement of the whole process. It must address all the current quality and safety (Q&S) standards. In this review article, an effective battery thermal management is sought considering the existing battery Q&S standards and scientific literature. The article contains a broad overview of the current existing standards and literature on a generic compliant BTMS. The aim is to assist in the design of a novel compatible BTMS. Additionally, the article delivers a set of recommendations to make an effective BTMS.

1 January 2014 in Journal of Power Sources
Verified
Journal Article
Closed access
Mohammad Rezwan KhanMohammad Rezwan Khan
Mohammad Rezwan Khan
GMGrietus Mulder
Grietus Mulder
JMJoeri Van Mierlo
Joeri Van Mierlo

1 April 2016
Verified
Conference Paper
Closed access
Mohammad Rezwan KhanMohammad Rezwan Khan
Mohammad Rezwan Khan
MSMaciej Swierczynski
Maciej Swierczynski
SKSoren Knudsen Kaer
Soren Knudsen Kaer
In this experiment-based research, there is an attempt to determine the evolution of surface temperature distribution, thermal behaviour and performance of a battery cell at the same time. The pouch type commercial test cell has a 13Ah capacity and Lithium Titanate Oxide (LTO) based anode. Temperatures on the surface of the cell are measured using contact thermocouples. Additionally, the heat flux is simultaneously measured with the isothermal calorimeter. This heat flux measurement is used for determining the heat generation inside the cell. Consequently, the important performance constituent of the battery cell efficiency is calculated. Those are accomplished at different temperature levels (0°C and 25°C) of continuous constant current 1C charge and discharge. Also, the maximal increase in the battery temperature over the cell surface is found on the battery cell surface. The heat flow calibration and experimentation for calorimetric measurement are deliberated. The experimental procedure is a very precise determination of the heat generation and the efficiency of the battery cell.

1 October 2016
Verified
Conference Paper
Closed access
Mohammad Rezwan KhanMohammad Rezwan Khan
Mohammad Rezwan Khan
SKSoren Knudsen Kaer
Soren Knudsen Kaer
A three-dimensional multiphysics-based thermal model of a battery pack is presented. The model is intended to demonstrate the cooling mechanism inside the battery pack. Heat transfer (HT) and computational fluid dynamics (CFD) physics are coupled for both time-dependent and steady-state simulation. Inside the battery cells in the pack a lumped value of heat generation (HG), that works as a volumetric heat source, is used. The measured HG stems from the cell level isothermal calorimeter experiment. The batteries inside the pack stay in the same initial thermal state in the simulation case. The pack is simulated to find the temperature gradient over the pack surfaces. Moreover, the temperature evolution results are simulated. It is demonstrated that the developed pack model can provide the thermal spatio-temporal behaviour with great detail. The result helps to understand the thermal behavior of the cells inside a battery pack.

1 April 2016
Verified
Conference Paper
Closed access
Mohammad Rezwan KhanMohammad Rezwan Khan
Mohammad Rezwan Khan
SKSoren Knudsen Kaer
Soren Knudsen Kaer
The research is focused on the development of a three-dimensional cell level multiphysics battery thermal model. The primary aim is to represent the cooling mechanism inside the unit cell battery pack. It is accomplished through the coupling of heat transfer and computational fluid dynamics (CFD) physics. A lumped value of heat generation (HG) inside the battery cell is used. It stems from isothermal calorimeter experiment. HG depends on current rate and the corresponding operating temperature. It is demonstrated that the developed model provides a deeper understanding of the thermal spatio-temporal behavior of Li-ion battery in different operating conditions.