This study explores the tribological performance of microwave-assisted synthesized g-C3N4/MoS2 coatings. The two-dimensional transition metal dichalcogenide (TMD) nanosheet is getting prominence in the study of tribology due to its layered structure. The graphitic carbon nitride (g-C3N4) nanosheet was made using the calcination method and its nanocomposite with molybdenum disulfide (MoS2) was produced using a microwave-assisted method. The structure and morphology of the samples were characterized by some well-known methods, and tribological properties were studied by a pin-on-disc (POD) apparatus. Morphological analysis revealed that graphitic carbon nitride and molybdenum disulfide coexisted, and the layer structured MoS2 was well dispersed on graphitic carbon nitride nanosheets. BET analysis was used to determine the pore volume and specific surface area of the synthesized materials. The inclusion of MoS2 nanoparticles caused the composite’s pore volume and specific surface area to decrease. The reduction in g-C3N4 pore volume and specific surface area confirmed that the pores of calcinated graphitic carbon nitride were filled with MoS2 nanoparticles. The tribological property of g-C3N4/MoS2 nanocomposite was systematically investigated under different factors such as applied loads (5N to 15N), sliding speed (500 to 1000 mm/s) and material composition (uncoated, MoS2-coated, 9 wt.% of g-C3N4 and 20 wt.% of g-C3N4 in the composite). The optimal composite material ratio was taken 9%, by weight of g-C3N4 in the g-C3N4/MoS2 composite for a variety of levels of loads and sliding speeds. The results indicates that the incorporation of g-C3N4 in nanocomposites could reduce friction and improve wear life, which were better than the results with single MoS2. This study demonstrates a solution to broaden the possible uses of g-C3N4 and MoS2-based materials in the field of tribology.
Mechanical components frequently come into contact against one another causing friction that produces heat at the contact area and wear of the components that shortens part life and increases energy consumption. In the current study, an attempt was made to optimize the parameters for the pin-on-disc wear tester. The experiments were carried out in ambient thermal conditions with varying sliding speeds (0.5 m/s, 0.75 m/s, and 1.0 m/s) and applied loads (5 N, 10 N, and 15 N) for pure molybdenum disulfide with 9% and 20% weight percentage of graphitic carbon nitride (g-C3N4) in molybdenum-disulfide (MoS2)-nanocomposite-coated steel substrate. Analysis of variance (ANOVA) was used to determine the outcome of interaction between various constraints. To identify the minimum wearing conditions, the objective was defined as the criterion ‘smaller is better’. The maximum impact of the applied load on the coefficient of friction and wear depth was estimated to be 59.6% and 41.4%, respectively, followed by sliding speed. The optimal condition for the minimum coefficient of friction and wear was determined to be 15 N for applied load, 0.75 m/s for sliding speed, and weight percentage of 9 for g-C3N4 in MoS2 nanocomposite. At the 95% confidence level, applied load was assessed to have the most significant effect on the coefficient of friction, followed by sliding speed and material composition, whereas material composition considerably impacts wear, followed by loading and sliding speed. These parameters show the effect of mutual interactions. Results from the Taguchi method and response surface methodology are in good agreement with the experimental results.
Excellent lubricating characteristics are shown by the solid lubricant MoS2, but due to its spontaneous oxidation and absorption of moisture from the air, it has low wearing resistance and a limited wear life. This study is the first to successfully mix the additive g-C3N4 with MoS2 using sophisticated microwave-assisted synthesis with controllable parameters in addition to traditional hydrothermal synthesis route. The conventional hydrothermal process takes longer than other approaches, such as microwave-assisted synthesis method. There was a lack of comparison between the two synthesis techniques in terms of pore size, morphology, and microstructure. This research evaluated the microstructure, morphology, surface area, and pore diameters of g-C3N4/MoS2 nanocomposite produced employing hydrothermal (g-C3N4/MoS2-HT) and novel microwave methods (g-C3N4/MoS2-MW). Request access from your librarian to read this chapter's full text.
9 June 2025 in Journal of the Brazilian Society of Mechanical Sciences and Engineering