Mohammed Waleed Qanbar

Mr. Mohammed Waleed Qanbar

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 August 2024 in Energies
Verified
Journal Article
Open access
PDF file
MQMohammed Waleed Qanbar
Mohammed Waleed Qanbar
Zekai HongZekai Hong
Zekai Hong
Hydrogen (H2) is positioned as a key solution to the decarbonization challenge in both the energy and transportation sectors. While hydrogen is a clean and versatile energy carrier, it poses significant safety risks due to its wide flammability range and high detonation potential. Hydrogen leaks can occur throughout the hydrogen value chain, including production, storage, transportation, and utilization. Thus, effective leak detection systems are essential for the safe handling, storage, and transportation of hydrogen. This review aims to survey relevant codes and standards governing hydrogen-leak detection and evaluate various sensing technologies based on their working principles and effectiveness. Our analysis highlights the strengths and limitations of the current detection technologies, emphasizing the challenges in achieving sensitive and specific hydrogen detection. The results of this review provide critical insights into the existing technologies and regulatory frameworks, informing future advancements in hydrogen safety protocols.

23 January 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
AAAyham AlAkhras
Ayham AlAkhras
ISIlham Hassan Sattar
Ilham Hassan Sattar
MAMuhammad Alvi
Muhammad Alvi
MQMohammed Waleed Qanbar
Mohammed Waleed Qanbar
MJMohammad A. Jaradat
Mohammad A. Jaradat
MAMuhannad Alkaddour
Muhannad Alkaddour
Conventionally, aerial manipulators, when used for inspection, use drone rotors to stabilize the center of gravity (CoG) shifts, which highly affects its performance. This paper discusses the development of a self-balancing lightweight cable aerial manipulator that can be used for construction inspection purposes. The design is based on a 3D-printed, three degrees of freedom (DoF), planar cable manipulator that is mounted on an extended platform below it as a counter-balance mechanism. The actuators control the manipulator links through a cable system, allowing them to be mounted at the system base to reduce the moving mass of the manipulator during operation. The counter-balance mechanism compensates for any shifts in the CoG of the system by actively sliding a counter-balance weight, mainly a battery, which powers the setup. This mechanism can be attached beneath an off-the-shelf quadrotor to solve the problem of CoG shifts. CoG shifts are due to the manipulator operation when a payload or inspection tool is attached to the end effector to perform a given task. For construction integrity inspection, the aerial manipulator must remain stable during the push or slide processes on both flat and curved surfaces while the non-destructive tests are carried out. To validate the effectiveness of the proposed design, an experimental setup was used, and comparisons were made between the compensated and uncompensated tilt angles of the aerial manipulator. Significant tilt angle reductions were observed with an average of 94.69% improvement, undergoing different manipulator motions during different operation scenarios, as a result of an active compensation of the CoG shift and lightweight design of the system, without sacrificing the functionality of the manipulator for the task.

31 October 2026 in Measurement: Sensors
Verified
Journal Article
Open access
MQMohammed Waleed Qanbar
Mohammed Waleed Qanbar
NUNicholas Utting
Nicholas Utting
JBJames Brydie
James Brydie
ZHZekai Hong
Zekai Hong

4 June 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
MQMohammed Waleed Qanbar
Mohammed Waleed Qanbar
NUNicholas Utting
Nicholas Utting
JBJames Brydie
James Brydie
Zekai HongZekai Hong
Zekai Hong
Hydrogen leak detection in hydrogen–methane environments is constrained by sensor cross-sensitivity and oxygen-dependent response mechanisms, particularly in subsurface storage and blended natural gas systems. This study experimentally evaluates a multi-mechanism hydrogen sensing system integrating catalytic combustion, infrared methane detection, and a palladium-based thin-film resistor. The catalytic–infrared pair estimates hydrogen concentration by correcting methane contributions using the infrared sensor, and its performance is characterized over a range of hydrogen–methane compositions and oxygen levels from normoxic to anoxic conditions. Under oxygen-sufficient conditions, the catalytic–infrared approach provides reliable hydrogen quantification, but exhibits systematic bias as oxygen availability decreases, with complete loss of functionality in oxygen-free environments. Sensor behavior is shown to be governed by oxygen availability relative to the stoichiometric oxygen demand, with methane-rich mixtures inducing earlier performance degradation. The thin-film resistor provides oxygen-independent hydrogen detection across all tested oxygen conditions, including oxygen-free environments, but undergoes irreversible drift under prolonged exposure to high hydrogen concentrations. Discrepancies between the catalytic–infrared and thin-film resistor readings provide a robust indicator of oxygen-deficient conditions and loss of catalytic sensing capability. These results quantify the benefits and limitations of combining catalytic, infrared, and thin-film resistor sensors for hydrogen monitoring in methane-containing and oxygen-limited environments, and inform the design of multi-mechanism sensing architectures for emerging hydrogen energy systems.