This article presents a mixed-mode electronically tunable first-order universal filter configuration employing only one voltage differencing gain amplifier (VDGA), one capacitor, and one grounded resistor. With the appropriate selection of the input signals, the proposed circuit can realize all three first-order standard filter functions, namely low pass (LP), high pass (HP), and all pass (AP), in all four possible modes, including voltage mode (VM), trans-admittance mode (TAM), current mode (CM), and trans-impedance mode (TIM), from the same circuit structure. It also provides an electronic tuning of the pole frequency and the passband gain by varying transconductance values. Non-ideal and parasitic effect analyses of the proposed circuit were also carried out. PSPICE simulations and experimental findings have both confirmed the performance of the design. A number of simulations and experimental observations confirm the viability of the suggested configuration in practical applications.
This paper proposes the design of a mixed-mode universal biquad configuration, which realizes generic filter functions in all four possible modes, namely voltage mode (VM), current mode (CM), transadmittance mode (TAM), and transimpedance mode (TIM). The filter architecture employs two voltage differencing buffered amplifiers (VDBAs), two resistors and two capacitors, and can provide lowpass (LP), bandpass (BP), highpass (HP), bandstop (BS), and allpass (AP) biquadratic filtering responses without any circuit alteration. All passive elements used are grounded, except VM. The circuit not only allows for the electronic tuning of the natural angular frequency (ωo), but also achieves orthogonal tunability of the quality factor (Q). It also provides the feature of availability of output voltage at the low-output impedance terminal in VM and TIM, and does not require inverting-type or double-type input signals to realize all the responses. Moreover, in all modes of operation, the high-Q filter can be easily obtained by adjusting a single resistance value. Influences of the VDBA nonidealities and parasitic elements are also discussed in detail. PSPICE simulations with TSMC 0.18-µm CMOS process parameters and experimental testing results with commercially available IC LT1228s have been used to validate the theoretical predictions.
This article presents the circuit designs for a mixed-mode universal biquadratic filter and a dual-mode quadrature oscillator, both of which use a single voltage differencing gain amplifier (VDGA), one resistor, and two capacitors. The proposed circuit has the following performance characteristics: (i) simultaneous implementation of standard biquadratic filter functions with three inputs and two outputs in all four possible modes, namely, voltage-mode (VM), current-mode (CM), trans-admittance-mode (TAM), and trans-impedance-mode (TIM); (ii) electronic adjustment of the natural angular frequency and independently single-resistance controllable high-quality factor; (iii) performing a dual-mode quadrature oscillator with simultaneous voltage and current output responses; (iv) orthogonal resistive and/or electronic control of the oscillation condition and frequency; (v) employing all grounded passive components in the quadrature oscillator function; and (vi) simpler topology due to the use of a single VDGA. VDGA non-idealities and parasitic elements are also investigated and analyzed in terms of their influence on circuit performance. To prove the study hypotheses, computer simulations with TSMC 0.18 μm CMOS technology and experimental confirmatory testing with off-the-shelf integrated circuits LM13600 have been performed.
This work presents the finite-time synchronization of a new six-term chaotic system with only stable equilibria and its circuitry implementation. The chaotic system is designed in such a way that its complex dynamical behavior, including hidden attractors, can be adjusted through only one parameter, whilst allowing transformation to chaotic flows via invariant transformations. A finite-time chaotic synchronizer is designed via a nonsingular terminal integral backstepping sliding mode controller, with reduced theoretical finite-time convergence, and a modified sliding surface, to accommodate analog circuitry implementations. A comparison between the proposed controller against conventional integral backstepping sliding mode controller showed that active synchronization is achieved in finite time. Finally, analog circuitry implementation for both open-loop and closed-loop configurations is realized via commercially available active components such as LF357 and AD633. The descriptive circuitry equations for both configurations are designed to mimic the actual governing control equations for simplicity and ease of circuit troubleshooting. The workability of both configurations was tested in OrCAD PSpice. Results show that the master and slave systems were found to be in synchronization with less than 0.95% maximum errors.
This study introduces four novel configurations of first-order and second-order multifunction inverse filters in both voltage-mode (VM) and current-mode (CM) using second-generation voltage conveyors (VCIIs). The first-order VM and CM inverse filters utilize only three passive components together with one VCII for VM and two VCIIs for CM realizations, which can provide lowpass and highpass inverse filter responses. The latter, second-order VM and CM multifunction inverse filters, can be constructed using the corresponding first-order inverse filters as their core circuits. These filters offer all the basic inverse filter functions, including lowpass, bandpass, and highpass inverse responses with all gains obtained from the same design. All the inverse filter realizations are cascadable. No component matching requirements are necessary for all filter responses. The non-ideal effects of the VCII on the performance of the proposed inverse filters are thoroughly examined. To prove the feasibility of the designs, the PSPICE program performed several simulations, utilizing model parameters of 0.18 µm CMOS technology. Some testing experiments were conducted using the commercially available IC-type AD844s for evaluating the practical performance of the designed inverse filters.
The design of a mixed-mode proportional-integral-derivative (PID) controller circuit using current-feedback operational amplifiers (CFOAs) as active components is proposed. With the same circuit topology, the proposed configuration of three CFOAs, four resistors, and two capacitors is capable of performing the PID controller in each of the following four modes: voltage mode, trans-admittance mode, current mode, and trans-impedance mode. Numerous mathematical analyses are conducted to determine the controller’s performance under both ideal and non-ideal conditions. Additionally, the mixed-mode second-order lowpass filter is suggested and also used to examine the workability of the proposed mixed-mode PID controller in a feedback control structure. The proposed PID controller is implemented with the commercially available IC-type CFOA AD844, and the simulation results are presented to illustrate the functionality of the controller and its closed-loop control system. According to the findings, the total power consumption of the proposed PID controller is 0.348 W, with symmetrical supply voltages of ±9 V. It also has a temperature variation of less than 0.2% over the AD844’s usable range. Monte Carlo statistical analysis results revealed that the gain responses of the controller exhibited a deviation of no more than 7.72% from the theoretical value. The controlled filter in a closed-loop control system has a 43% faster rise time and peak time than the uncontrolled filter in all four modes of operation. It also has a steady-state error less than 0.2 mV for voltage responses and 0.72 µA for current responses.
About Me
School of Engineering, King Mongkut’s Institute of Technology Ladkrabang (KMITL), Bangkok 10520, Thailand
School of Engineering, King Mongkut’s Institute of Technology Ladkrabang (KMITL), Bangkok 10520, Thailand