Railway industries are placing greater emphasis on implementing fast and heavy haul corridors for bulk freight and commuter transport in order to deliver more efficient and cost-effective services. However, increasing dynamic stresses from the passage of trains progressively degrades and fouls the primary load-bearing ballast layer, which inevitably leads to excessive settlement and instability, damage to track elements, and more frequent maintenance. Ballasted tracks are subjected to even greater stresses and faster deterioration in sections where a reduced ballast thickness is used (e.g., bridge decks) or at locations where heavier concrete sleepers are used instead of lightweight timber sleepers. The inclusion of under sleeper pads (USPs) at the base of a concrete sleeper is one measure used to minimize dynamic stresses and subsequent track deterioration. In this study, cyclic loads from fast and heavy haul trains were simulated using a large-scale process simulation prismoidal triaxial apparatus (PSPTA) to investigate the performance of ballast improved by USPs. The laboratory results indicate that the inclusion of an elastic element at the harder interface of the concrete sleeper–ballast reduces the stresses transmitted to the ballast and the underlying layers and minimizes the amount of deformation and degradation of the ballast. A three-dimensional finite-element model was used to predict the behavior of ballast, and the influence of USPs on the stress–strain responses of ballast generally agree with the experimental findings.
1 June 2017 in Journal of Geotechnical and Geoenvironmental Engineering
The deterioration of a rail track due to large dynamic wheel loads is inevitable over the years and leads to frequent, high-cost maintenance. This problem is more critical in isolated rail track locations such as bridges and tunnels, where the substructure is much stiffer than the surface track assembly. One measure used to minimize track deterioration is geosynthetic inclusions such as rubber mats under the layer of ballast. In this study, cyclic loads from fast and heavy-haul trains were simulated on stiffer track foundation conditions using a large-scale process simulation triaxial (prismoidal) apparatus (PSPTA) to investigate the performance of ballast improved by rubber mats locally manufactured from recycled tires. The laboratory results indicate that the energy-absorbing (damping) characteristics of rubber mats reduce the amount of deformation and degradation of ballast under stiffer track conditions. The study shows that rubber mats distribute the stress applied from moving trains more uniformly by increasing the effective contact area, which then reduces the dynamic amplification of applied vertical stress and leads to much less ballast degradation.
1 February 2022 in Proceedings of the Institution of Civil Engineers - Ground Improvement
Recycling waste materials for transport infrastructure such as coal wash (CW), steel furnace slag (SFS), fly ash (FA) and recycled tyre products is an efficient way of minimising the stockpiles of waste materials while offering significant economic and environmental benefits, as well as improving the stability and longevity of infrastructure foundations. This paper presents some of the most recent state-of-the-art studies undertaken at the University of Wollongong, Australia on the use of waste materials such as (a) CW-based granular mixtures (i.e. SFS + CW, CW + FA) for port reclamation and road base/subbase and (b) using recycled tyre products (i.e. rubber crumbs, tyre cell, under-sleeper pads and under-ballast mats) to increase track stability and reduce ballast degradation. Typical methods of applying these waste materials for different infrastructure conditions are described and the results of comprehensive laboratory and field tests are presented and discussed.
Rail track substructure (ballast, subballast and subgrade) is the most essential component of the railway system in view of track stability. The ballast is the largest component of the track substructure and it is the key load-bearing stratum packed with rock aggregates underneath and around the sleepers, thereby providing structural support against dynamic stresses caused by moving trains. However under large dynamic stresses exerted by heavy haul and high speed trains, the degradation of track substructure including ballast becomes significant. This in turn affects the track stability and creates frequent maintenance, thus increasing the life cycle cost of the rail network. Therefore, mitigating degradation of the ballast layer is vital in view of track longevity. In recent years, the use of resilient soft pads (shock mats) above the ballast (i.e. Under Sleeper Pad, USP) and below the ballast (i.e. Under Ballast Mat, UBM) has become a common practice. Many countries, including Australia have adopted the use of resilient pads in the rail track foundation. Currently, the studies on resilient mats are mostly limited to the reduction of vibration and noise. There is a lack of proper assessment of the geotechnical behavior of ballast when used along with shock mats. This paper provides an assessment of the triaxial behavior of the track substructure with and without shock mats under dynamic loading condition. A numerical model was developed based on the modified stress-dilatancy approach to capture the stress-strain and volume change behavior of ballast during impact loading. Model predictions are compared with laboratory results. It was found that the shock mats provide significant advantages in terms of reduced particle breakage and enhanced track stability
The shear resistance at the sleeper–ballast interface of a ballasted track is an important contributor in maintaining track stability under faster and heavier axle loads where the ballast undergoes significant lateral sliding. Different types of sleeper–ballast interfaces based on the type of sleeper arrangements, such as concrete sleepers, timber sleepers, and under sleeper pads (USPs) attached to the concrete sleepers influence the lateral stability of railway tracks. Therefore, in this study the shear and degradation behaviour of ballast at concrete–ballast, timber–ballast, and USP–ballast interfaces were examined in the laboratory using large-scale direct shear tests under 60 kPa normal stress. The use of waste materials in the construction of civil infrastructure is gaining a lot of interest in the engineering community. Therefore, in addition to commercial USPs manufactured using raw materials, recycled USPs manufactured from granulates of end-of-life rubber tyres were also tested in this study. The discrete element modelling (DEM) approach was used to predict the shear behaviour of ballast at 30, 90, 120, 150, and 180 kPa normal stresses. The bonded particle model (BPM) was adopted in the DEM to simulate the effects of particle breakage during shearing. The results exhibited that both commercial and recycled USPs significantly improve the shear resistance at the sleeper–ballast interface while reducing particle degradation compared to concrete and timber sleeper interfaces.