Neda Asasian-Kolur

Dr. Neda Asasian-Kolur

TU Wien, Vienna, Wien, Austria

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 June 2022 in Materials
Verified
Journal Article
Open access
PDF file
SMSeyed Heydar Mosavi Mirak
Seyed Heydar Mosavi Mirak
SSSeyedmehdi Sharifian
Seyedmehdi Sharifian
FSFatemeh Esmaeili Khalil Saraei
Fatemeh Esmaeili Khalil Saraei
Neda Asasian-KolurNeda Asasian-Kolur
Neda Asasian-Kolur
BHBahram Haddadi
Bahram Haddadi
Michael HarasekMichael Harasek
Michael Harasek
Titanium-pillared clay (Ti-PILC), as one of the most suitable types of porous adsorbents/(photo)catalysts, was prepared from a local type of Iranian clay and titanium isopropoxide. The production process was optimized by changing three operating parameters, including the clay suspension concentration (in the range of 0.5–10% w/v), the H+/Ti ratio (2–8 mol/mol), and the calcination temperature (300–700 °C). The largest specific surface area for the Ti-PILC was about 164 m2/g under the clay suspension of 0.5% w/v, H+/Ti = 6, with a surface area 273% larger than that of the raw clay. The surface areas obtained from more concentrated clay suspensions were, however, comparable (159 m2/g for 3% w/v clay and H+/Ti = 4). An increase in the calcination temperature has a negative effect on the porous texture of Ti-PILC, but based on modeling with artificial neural networks, its contribution was only 7%. Clay suspension and H+/Ti ratio play a role of 56 and 37% of the specific surface area. The presence of rutile phase, and in some cases anatase phase of TiO2 crystals was detected. FTIR and SEM investigations of Ti-PILCs produced under different operating parameters were analyzed.

29 April 2022 in Membranes
Verified
Journal Article
Open access
PDF file
AMAmir Jahed mogharrab
Amir Jahed mogharrab
SSSeyedmehdi Sharifian
Seyedmehdi Sharifian
Neda Asasian-KolurNeda Asasian-Kolur
Neda Asasian-Kolur
AGAli Ghadimi
Ali Ghadimi
BHBahram Haddadi
Bahram Haddadi
Michael HarasekMichael Harasek
Michael Harasek
The present work studied an air-to-air exchanger comprising a flat plate module with a diagonal channel and a counterflow configuration for the air streams. The objective of this study was to remove moisture and sensible heat from an exhaust air stream by indirect contact with another air stream. The temperature and flow rate of the exhaust air was in the range of 40–80 °C and 1–5 L·min−1, respectively, and the fresh ambient air to exhaust air flow ratio was 1–5. An asymmetric porous membrane (P-MEM), a thin film composite membrane (C-MEM), and a kraft paper were used as the core for the heat exchange module. The most influential parameter was the humid air temperature, with a direct positive effect (50–60%) due to the increase in the kinetic energy of the water molecules. The other effective parameter was the flow rate of the humid gas with a reverse effect on the enthalpy exchanger performance (25–37%). The ratio of “fresh” air to “exhaust” air had the lowest positive effect (8–10%) on the total effectiveness. The sensible effectiveness of different membranes under the studied conditions was relatively the same, showing their similar heat conductivity. However, the kraft paper showed the best performance compared to the synthetic membranes due to having a porous/hydrophile texture. P-MEM with an asymmetric porous texture showed the closest performance to kraft paper. Furthermore, it was found that under limited conditions, such as higher temperatures (70 and 80 °C) and flow rates (5 L·min−1) for the humid air, the performance of P-MEM was a little better than the kraft paper. However, C-MEM with the lowest total effectiveness and overall heat transfer coefficient (150–210 W·m−2·K−1) showed that the hydrophile PEBAX layer could not contribute to moisture recovery due to its high thickness.

20 February 2026 in Molecules
Verified
Journal Article
Open access
PDF file
SDSeyedehreyhane Aghaei Dinani
Seyedehreyhane Aghaei Dinani
Neda Asasian-KolurNeda Asasian-Kolur
Neda Asasian-Kolur
Michael HarasekMichael Harasek
Michael Harasek
Biochar activation is critical for producing high-performance adsorbents; however, conventional activation methods are energy-intensive and difficult to control, particularly when air is used as an activating agent. This study investigates CO2–air co-activation in a laboratory-scale fluidized bed reactor as an energy-efficient alternative. Experiments were conducted at 750–850 °C under varying gas flow rates with a constant CO2/O2 ratio. Optimal properties were achieved at 800 °C and 0.2–0.3 L/min CO2, yielding a maximum BET surface area of 479 m2/g, a micropore contribution of 42%, and controlled carbon conversion (~25–35% yield). Aspen Plus equilibrium simulations also confirm that CO2-only activation remains endothermic (heat duty up to +0.07 kW), air-only activation becomes strongly exothermic (down to −0.13 kW), while the CO2–air mixture exhibits near-thermoneutral to mildly exothermic behavior (+0.13 to −0.10 kW), thereby reducing external energy demand potentially by approximately 60–70% compared with CO2-only activation and significantly improving process stability. These results demonstrate that CO2–air co-activation offers a practical route to produce high-quality activated biochar with controlled porosity and improved energy efficiency.