Novel EDOT based bent-core and hockey-stick shaped mesogens bearing terminal alkyl chains and alkoxy terminal chains, respectively, have been designed and synthesized via the Sonogashira coupling reaction. Molecular structures of these new compounds were determined using spectral and elemental analysis. The mesomorphic behaviour of all the novel compounds was primarily investigated by a combination of polarising optical microscopy (POM), differential scanning calorimetry (DSC) and X-ray diffraction studies (XRD). All of the compounds exhibit an enantiotropic nematic phase in lower homologs. However, a smectic A phase at a lower temperature along with the high temperature nematic phase was observed in higher homologs of BC and hockey-stick LCs. A density functional theory study was carried out to investigate the stable configuration. The bent angle of these molecules was intermediate between calamitic LCs and banana LCs. The photophysical properties of all the compounds were studied in anhydrous chloroform solvent and show absorption patterns around 370–395 nm and emission between 418–465 nm. We have also reported large effective two-photon absorption in these novel compounds when measured under excitation by nanosecond laser pulses at 532 nm. All of the mesogenic compounds are nonlinear materials, which make them suitable candidates for optical limiting applications.
Novel π-extended phenazine fused triphenylene discotic liquid crystals show an enantiotropic columnar mesophase and good photophysical and nonlinear optical properties.
Nanoparticles generated during laser material processing are often seen as annoying side products, yet they might find useful application upon proper collection. We present a parametric study to identify the dominant factors in nanoparticle removal and collection with the goal of establishing an in situ removal method during femtosecond laser machining. Several target materials of different electrical resistivity, such as Cu, Ti, and Si were laser machined at a relatively high laser fluence. Machining was performed under three different charge conditions, i.e., machining without an externally applied charge (alike atmospheric pulsed laser deposition (PLD)) was compared to machining with a floating potential and with an applied field. Thereby, we investigated the influence of three different charge conditions on the behavior of laser-generated nanoparticles, in particular considering plume deflection, nanoparticle accumulation on a collector plate and their redeposition onto the target. We found that both strategies, machining under a floating potential or under an applied field, were effective for collecting laser-generated nanoparticles. The applied field condition led to the strongest confinement of the nanoparticle plume and tightest resulting nanoparticle collection pattern. Raster-scanning direction was found to influence the nanoparticle collection pattern and ablation depth. However, the laser-processed target surface remained unaffected by the chosen nanoparticle collection strategy. We conclude that machining under a floating potential or an applied field is a promising setup for removing and collecting nanoparticles during the machining process, and thus provides an outlook to circular waste-free laser process design.
Laser-induced periodic surface structuring is a powerful technique for modifying the surface properties of solids. Using ultrashort pulses from a Ti:sapphire laser (800 nm, 100 fs), we have fabricated nanoscale order laser-induced periodic surface structures (LIPSSs) on a silicon (100) surface. The LIPSS patterns are found to be strongly dependent on the laser pulse energy, state of polarization, number of shots delivered on the target, and the ambient pressure. The role of laser wavelength is studied by using the second harmonic output (400 nm) also for fabrication. Large area (5 × 4 mm2) surface structuring has been carried out at atmospheric pressure after optimizing the laser parameters at 800 nm. The patterned silicon surface shows a substantial reduction in the reflection of incident light over a wide range of wavelengths, in comparison to plain silicon. Moreover, when used for laser induced breakdown spectroscopy experiments, enhanced optical emission and ion current have been observed from the patterned surface. This indicates that the coupling of laser energy to the surface is enhanced in the case of patterned silicon. While spectral lines emitted by doubly ionized silicon have been observed from the patterned surface, the plain surface gives lines from singly ionized silicon only. A discernible enhancement has been measured in both optical (50%–90%) and electrical (34%) signals from the plasma generated on the patterned surface. These results confirm that LIPSS is a versatile method for enhancing the coupling of laser energy onto irradiated solid surfaces.
In this report we investigate the performance of various beam shutter technologies when applied to femtosecond laser micromachining. Three different shutter options are considered: a mechanical blade shutter, a bistable rotary solenoid shutter, and an electro-optic modulator (EOM) shutter. We analyzed the behavior of each shutter type during repeated open/close commands (period of 10 ≤ T ≤ 200 ms) using both high-speed videography and practical micromachining experiments. To quantify the performance at varying cycle periods, we introduce a new variable called the compliance that characterizes the average state of the shutter with respect to its intended position. We found that the solenoid shutter responds poorly to sequential commands. The mechanical shutter provides reliable performance for cycled commands as short as T = 40 ms, but begins to lag significantly behind the control signal for T ≤ 20 ms. The EOM shutter provides the most precise and reliable performance, with an opening time of only 0.6 ms and a high compliance with the signal commands, even when cycled very quickly (T = 10 ms). Overall, this study acts as an extensive practical guide for other laser users when considering different shutter options for their laser system and desired application.