Odin Reyes Vallejo

Dr. Odin Reyes Vallejo

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 December 2024 in Sustainability
Verified
Journal Article
Open access
PDF file
Francisco Javier CanoFrancisco Javier Cano
Francisco Javier Cano
Odin Reyes VallejoOdin Reyes Vallejo
Odin Reyes Vallejo
R M Sanchez-AlboresR M Sanchez-Albores
R M Sanchez-Albores
JPjoseph sebastian Pathiyamattom
joseph sebastian Pathiyamattom
Abumalé Cruz-SalomónAbumalé Cruz-Salomón
Abumalé Cruz-Salomón
HTHector Hiram Torres-Ventura
Hector Hiram Torres-Ventura
Renowned for its versatility in environmental applications, biochar exhibits substantial potential to enhance anaerobic digestion, facilitate carbon sequestration, and improve water treatment through its highly efficient adsorption mechanisms. This study focuses on biochar derived from pineapple crown biomass, produced through slow pyrolysis, and its efficiency in removing organic dyes from contaminated water. The structural, morphological, and surface properties of both biochar and chemically activated biochar samples were comprehensively characterized using a range of techniques, including XRD, FTIR, XPS, BET surface area analysis, and SEM microscopy. The adsorption performance was evaluated using methylene blue (MB), rhodamine B (RhB), and malachite green (MG) dyes as model contaminants, with particular emphasis on the contact time on dye removal efficiency. Initial results showed removal rates of 10.8%, 37.5%, and 88.4% for RhB, MB, and MG, respectively. Notably, chemical activation significantly enhanced the adsorption efficiency, achieving complete (100%) removal of all tested dyes. Complete adsorption of MB and MG occurred within 9 min, indicating rapid adsorption kinetics. Adsorption data fit well with pseudo-second-order kinetics (R2 = 0.9748–0.9999), and the Langmuir isotherm (R2 = 0.9770–0.9998) suggested monolayer adsorption with chemical interactions between dyes and biochar. The intraparticle diffusion model further clarified the adsorption mechanisms. These findings demonstrate the efficacy of activated biochar for dye removal and highlight the potential of pineapple crown biomass in environmental remediation.

31 March 2025 in Environmental Science and Pollution Research
Verified
Journal Article
Open access
PDF file
Odin Reyes VallejoOdin Reyes Vallejo
Odin Reyes Vallejo
RSRocío Magdalena Sánchez-Albores
Rocío Magdalena Sánchez-Albores
JEJosé Escorcia-García
José Escorcia-García
Abumalé Cruz-SalomónAbumalé Cruz-Salomón
Abumalé Cruz-Salomón
PBPascual Bartolo-Pérez
Pascual Bartolo-Pérez
HEHéctor Armando Esquinca-Avilés
Héctor Armando Esquinca-Avilés
The efficient removal of synthetic dyes, such as methylene blue (MB) and malachite green (MG), continues to pose a significant challenge due to their high stability, toxicity, and resistance to conventional treatment methods. In this study, CaO-Fe₃O₄ compounds were synthesized using a sustainable ball-milling technique, utilizing calcium oxide derived from eggshells and Fe₃O₄. The compounds were calcined at temperatures ranging from 200 to 800 °C to optimize their structural and photocatalytic properties. The sample calcined at 400 °C exhibited the highest surface area (17.86 m2/g), the narrowest bandgap (2.10 eV), and the coexistence of CaO, Ca(OH)₂, and γ-Fe₂O₃ phases, making it an ideal candidate for achieving high dye removal efficiency. Under visible light, this sample completely degraded MB at 10 ppm within 30 min, following pseudo-first-order kinetics with a rate constant (kₐₚₚ) of 0.110 min−1 and a half-life (t₁/₂) of 6.30 min. At an MB concentration of 50 ppm, complete degradation was achieved in 90 min. Radical scavenging experiments indicated that superoxide radicals (·O₂−) played a key role in the degradation mechanism. For MG (100 ppm), the maximum adsorption capacity (qₑ) was 1111.11 mg/g, fitting the Langmuir model (R 2 = 0.996) with an equilibrium constant (K L) of 0.6822 L/mg, indicating a highly favorable process. The adsorption kinetics followed a pseudo-second-order model (R 2 ≈ 0.999), suggesting chemisorption as the rate-limiting step. Thermodynamic parameters confirmed that MG adsorption was spontaneous and endothermic, with negative Gibbs free energy, positive enthalpy, and increased entropy. This study proposes an eco-friendly and efficient approach for dye removal, integrating waste valorization. Graphical Abstract

15 April 2025 in Journal of Materials Science: Materials in Electronics
Verified
Journal Article
Open access
PDF file
Francisco Javier CanoFrancisco Javier Cano
Francisco Javier Cano
RSRocío Sánchez−Albores
Rocío Sánchez−Albores
AAA. Ashok
A. Ashok
JEJ. Escorcia−García
J. Escorcia−García
ACA. Cruz−Salomón
A. Cruz−Salomón
SVS. Velumani
S. Velumani
Biochar is emerging as a sustainable material for addressing critical environmental challenges, including water pollution and carbon sequestration. In this study, biochar derived from papaya seed biomass via slow pyrolysis was investigated for its efficacy in removing organic dyes from aqueous solutions. Both biochar and chemically functionalized biochar were comprehensively characterized using XRD, FTIR, XPS, BET surface area analysis, and SEM/EDS to elucidate their structural, morphological, and surface properties. The adsorption performance was assessed using methylene blue (MB), rhodamine B (RhB), malachite green (MG), and methyl orange (MO) as model contaminants, with particular attention to adsorption kinetics and equilibrium behavior. The unmodified biochar exhibited moderate adsorption capacities, primarily driven by π − π interactions and a limited number of functional groups, achieving removal efficiencies of 55.5, 97.8, and 12.9% for MB, MG, and RhB, respectively, while MO showed negligible adsorption. Remarkably, chemical functionalization with KMnO₄ significantly enhanced biochar performance, increasing surface area and functional group diversity. This modification enabled the complete removal (100%) of MB and MG within six minutes, alongside substantial improvements for RhB and MO, achieving 100 and 88% removal, respectively. Adsorption kinetics followed a pseudo‒second‒order model (R 2 > 0.99), indicating chemisorption as the dominant mechanism, while Langmuir isotherms (R 2 = 0.993 − 0.999) suggested monolayer adsorption. Additionally, the intraparticle diffusion model highlighted the synergistic contributions of surface interactions and pore diffusion to overall adsorption efficiency. These findings establish chemically functionalized papaya seed biochar as a highly efficient, low‒cost adsorbent for dye removal, underscoring its potential for environmental remediation. The innovative utilization of papaya seed biomass not only adds value to agricultural waste but also advances sustainable water treatment strategies, reinforcing its significance in environmental science and engineering.

16 March 2023 in Journal of Materials Science: Materials in Electronics
Verified
Journal Article
Open access
PDF file
Odin Reyes VallejoOdin Reyes Vallejo
Odin Reyes Vallejo
RSRocío Sánchez-Albores
Rocío Sánchez-Albores
AMA. Maldonado-Álvarez
A. Maldonado-Álvarez
AAA. Ashok
A. Ashok
JDJ. C. Duran-Alvarez
J. C. Duran-Alvarez
VSVelumani Subramaniam
Velumani Subramaniam
In this study, the synthesis of Calcium–Magnesium oxide through the ball milling method using eggshell as a CaO source, developing an ecological process synthesis, is presented. After ball milling, an annealing process was carried out in order to increase the crystallinity of the material to enhance its optoelectronic properties by varying the temperature from 450 to 900 °C. The samples were analyzed by X-ray diffraction, Raman and UV–Vis spectroscopy, FE-SEM, photoluminescence, and BET analysis. The ball milling process itself promoted a reduction in particle size, which increased slightly during the annealing process, achieving a more homogeneous size distribution and improving its crystallinity, according to XRD and Raman spectroscopy. The samples were tested for the photodegradation of methylene blue (100 mL of a 10 ppm solution), using LED lamps (200 W). The best photodegradation performance was recorded with the sample annealed at 750 °C, which is explained by the more homogeneous size distribution and the greater surface area, a smaller band gap, and fewer surface defects, which causes greater absorption of light, a better transport of the charge carriers and consequently a better performance in the photodegradation of MB. The complete removal of MB was achieved in 20 min under sunlight stimulation, which can be reducedto 12 min using 400 mg of the catalyst. On the other hand, the trapping experiment showed that superoxide radicals (·O2−) and holes (h+) are the key reactive species in the photodegradation process of MB. The kinetic study showed to follow a pseudo-first-order for all cases. These photodegradation results reported for the first time are better than those reported in other Calcium–Magnesium oxide synthesized by combustion or ultrasound-assisted methods.

17 July 2025 in Journal of Materials Science: Materials in Electronics
Verified
Journal Article
Open access
PDF file
Odin Reyes VallejoOdin Reyes Vallejo
Odin Reyes Vallejo
FCFrancisco J. Cano
Francisco J. Cano
R M Sanchez-AlboresR M Sanchez-Albores
R M Sanchez-Albores
ELEdith Luévano-Hipólito
Edith Luévano-Hipólito
RSR. P. Serrano-Ramirez
R. P. Serrano-Ramirez
SVS. Velumani
S. Velumani
The transition toward sustainable synthesis routes plays a crucial role in advancing scalable and environmentally responsible photocatalytic materials. In this study, a green combustion synthesis of bismuth vanadate (BiVO4) was developed, using orange peel powder (OPP) as both a renewable fuel and a multifunctional complexing agent. The incorporation of OPP eliminated the need for hazardous reagents and promoted waste valorization, aligning with the principles of green chemistry and the circular economy. Comprehensive structural, morphological, and optical characterizations were performed using XRD, Raman, XPS, FTIR, SEM/TEM, and UV–Vis spectroscopy. An increasing OPP content induced a phase transition from a mixed tetragonal-monoclinic system to a predominantly monoclinic BiVO4 structure, which correlated with improved photocatalytic performance. Although the residual organic components of OPP were not explicitly identified, the data indicated enhanced crystallinity and the formation of oxygen vacancies. These vacancies contributed to bandgap narrowing (2.21 eV), improved charge separation, and reduced electron–hole recombination. The optimized BiVO4 sample (N3-350) exhibited remarkable photocatalytic activity, achieving over 95% degradation of methylene blue and malachite green, and 80% of acid blue 113 under visible-light irradiation. Electrochemical measurements revealed an increase in charge carrier density and favorable band edge alignment, supporting efficient photocatalytic hydrogen evolution (163 μmol H2 g⁻1 h⁻1) and CO2 photoreduction to formic acid (46.9 μmol h⁻1), all without the need for noble metal cocatalysts. This green synthesis approach for BiVO4 demonstrates the effectiveness of biomass-derived materials in photocatalytic and environmental applications and provides a viable pathway for sustainable materials design.

2 May 2018 in Journal of Materials Science: Materials in Electronics
Verified
Journal Article
Closed access
PDF file
Odin Reyes VallejoOdin Reyes Vallejo
Odin Reyes Vallejo
DMD. Maldonado
D. Maldonado
JEJ. Escorcia-García
J. Escorcia-García
JPjoseph sebastian Pathiyamattom
joseph sebastian Pathiyamattom