Rolando Orense

Prof. Rolando Orense

University of Auckland, Auckland, New Zealand
orcid

Research Focus & Metrics

Academic Career Length

29Years (1998-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 December 2010 in Bulletin of the New Zealand Society for Earthquake Engineering
Verified
Journal Article
Open access
PDF file
MCMisko Cubrinovski
Misko Cubrinovski
RGRussell A. Green
Russell A. Green
JAJohn Allen
John Allen
SAScott Ashford
Scott Ashford
EBElisabeth Bowman
Elisabeth Bowman
LWLiam Wotherspoon
Liam Wotherspoon
On 4 September 2010, a magnitude Mw 7.1 earthquake struck the Canterbury region on the South Island of New Zealand. The epicentre of the earthquake was located in the Darfield area about 40 km west of the city of Christchurch. Extensive damage was inflicted to lifelines and residential houses due to widespread liquefaction and lateral spreading in areas close to major streams, rivers and wetlands throughout Christchurch and Kaiapoi. Unreinforced masonry buildings also suffered extensive damage throughout the region. Despite the severe damage to infrastructure and residential houses, fortunately, no deaths occurred and only two injuries were reported in this earthquake. From an engineering viewpoint, one may argue that the most significant aspects of the 2010 Darfield Earthquake were geotechnical in nature, with liquefaction and lateral spreading being the principal culprits for the inflicted damage. Following the earthquake, an intensive geotechnical reconnaissance was conducted to capture evidence and perishable data from this event. The surveys were performed on foot, by car and from a helicopter over a period of six days. A broad-brush field reconnaissance was conducted in the first two days, followed by pin-point investigations at specific locations including detailed site inspections and field testing using: Dynamic Cone Penetration Test (DCPT), Swedish Weight Sounding (SWS), and Spectral Analysis of Surface Waves (SASW). This paper summarizes the observations and preliminary findings from this early reconnaissance work.

13 August 2012 in New Zealand Journal of Geology and Geophysics
Verified
Journal Article
Closed access
MCM Cubrinovski
M Cubrinovski
KRK Robinson
K Robinson
MTM Taylor
M Taylor
MHM Hughes
M Hughes
Rolando OrenseRolando Orense
Rolando Orense
In the 4 September 2010 ( M W =7.1) and 22 February 2011 ( M W =6.2) earthquakes, widespread liquefaction and lateral spreading occurred throughout Christchurch and the town of Kaiapoi. The severe soil liquefaction and lateral spreading in particular caused extensive and heavy damage to residential buildings, Christchurch business district (CBD) buildings, bridges and water supply and wastewater systems of Christchurch. After the earthquake, comprehensive field investigations and inspections were conducted to document the liquefaction‐induced land damage and lateral spreading displacements and their impact on buildings and infrastructure. The results of ground surveying measurements of lateral spreads at approximately 120 locations along the Avon River, Kaiapoi River and streams in the affected area reveal permanent lateral ground displacements at the banks of up to 2–3 m that progressed inland as far as 200–250 m from the waterway, causing significant damage to structures located within the spreading zone. Different features and magnitudes of spreading were identified, which were often affected by a complex interplay of ground conditions, topography, meandering river geometry and local depositional environment. The spreading was characterised by very large and highly non‐uniform ground deformation causing stretching of building foundations and the buildings themselves. Road bridges suffered a characteristic spreading‐induced damage mechanism including back‐rotation of the abutments associated with deck pinning and damage at the top of the abutment piles. The wastewater system of Christchurch was hit particularly hard by the liquefaction and lateral spreading, and approximately 60% of the damaged pipes of the potable water system were located in areas of severe liquefaction and lateral spreading.

1 April 2013 in Journal of Geotechnical and Geoenvironmental Engineering
Verified
Journal Article
Closed access
TKTakashi Kaneko
Takashi Kaneko
Rolando OrenseRolando Orense
Rolando Orense
Masayuki HyodoMasayuki Hyodo
Masayuki Hyodo
Norimasa YoshimotoNorimasa Yoshimoto
Norimasa Yoshimoto
With the objective of better and more environmentally friendly recycling methods, many researchers are now examining the use of scrap tires as a new geomaterial. Based on past research, it was clear that tire chips reduce the rise of excess pore-water pressure when subjected to earthquake shaking. Based on such characteristics, online pseudodynamic response tests were conducted in this study on model grounds consisting of either tire chip-mixed sand or alternating layers of sand and tire chips with the aim of clarifying the seismic response characteristics of tire chips and tire chip-sand mixtures. Online testing is a method of feeding soil response characteristics directly from soil samples into a one-dimensional modeling algorithm. The test results showed that when tire chips with low stiffness were either mixed with sand or placed as layers, more significant damping and seismic isolation effects were observed. The presence of tire chips also reduced the accumulation of excess pore-water pressure in the layer, preventing the occurrence of liquefaction. In addition, when tire chips are installed as layers beneath the sand, liquefaction is not generated in the upper sandy layer because the amplitudes of the seismic waves are attenuated. Finally, the effectiveness of tire chips mixed with sand increased as the mix ratio was increased. When they were installed as pure layers, tire chips were more effective when placed at a deeper location or when the layer was thicker.

1 July 1999 in Soil Dynamics and Earthquake Engineering
Verified
Journal Article
Closed access
ITI Towhata
I Towhata
WVW Vargas-Monge
W Vargas-Monge
Rolando OrenseRolando Orense
Rolando Orense
MYM Yao
M Yao

1 June 2019 in Géotechnique
Verified
Journal Article
Closed access
GPG. S. Pardo
G. S. Pardo
ASA. K. Sarmah
A. K. Sarmah
Rolando OrenseRolando Orense
Rolando Orense
Biochar is a biomass-derived carbonaceous solid product produced by way of pyrolysis, a process whereby thermal degradation of biomass occurs in the absence of or under a limited oxygen environment. To date, little work has been done to assess its effect on soil properties from the geotechnical point of view. A few studies have shown that biochar could increase the shear strength of clays. Results of simple shear tests indicated that although the effect of adding biochar on the drained shear resistance of sand is relatively minor, the liquefaction resistance increased considerably. In this paper, to provide an insight into the mechanism, the interaction between biochar and water was studied in more detail, through an analysis of the biochar chemical active surface, morphological observations of the particles and biochar–water suspension, as well as rheological measurements. It is believed that the mechanism of improvement is related to the active chemicals on the surface and inside the pores of the biochar particles. These volatiles interact with water by repelling it (hydrophobic) and at times by attracting it (hydrophilic), creating a complex network between water and biochar particles that helps to delay the increase in excess pore-water pressure and provides some shear resistance.

1 January 2012 in Engineering Geology
Verified
Journal Article
Closed access
LWLiam M. Wotherspoon
Liam M. Wotherspoon
MPMichael J. Pender
Michael J. Pender
Rolando OrenseRolando Orense
Rolando Orense