Museum contents are vulnerable to bad ambience conditions and human vandalization. Preserving the contents of museums is a duty towards humanity. In this paper, we develop an Internet of Things (IoT)-based system for museum monitoring and control. The developed system does not only autonomously set the museum ambience to levels that preserve the health of the artifacts and provide alarms upon intended or unintended vandalization attempts, but also allows for remote ambience control through authorized Internet-enabled devices. A key differentiating aspect of the proposed system is the use of always-on and power-hungry sensors for comprehensive and precise museum monitoring, while being powered by harvesting the Radio Frequency (RF) energy freely available within the museum. This contrasts with technologies proposed in the literature, which use RF energy harvesting to power simple IoT sensing devices. We use rectenna arrays that collect RF energy and convert it to electric power to prolong the lifetime of the sensor nodes. Another important feature of the proposed system is the use of deep learning to find daily trends in the collected environment data. Accordingly, the museum ambience is further optimized, and the system becomes more resilient to faults in the sensed data.
IoT system becomes a hot topic nowadays for smart home. IoT helps devices to communicate together without human intervention inside home, so it is offering many challenges. A new smart home IoT platform powered using electromagnetic energy harvesting is proposed in this paper. It contains a high gain transmitted antenna array and efficient circularly polarized array rectenna system to harvest enough power from any direction to increase lifetime of the batteries used in the IoT system. Optimized energy consumption, the software with adopting the Zigbee protocol of the sensor node, and a low-power microcontroller are used to operate in lower power modes. The proposed system has an 84.6-day lifetime which is approximately 10 times the lifetime for a similar system. On the other hand, the proposed power management circuit is operated at 0.3 V DC to boost the voltage to ~3.7 V from radio frequency energy harvesting and manage battery level to increase the battery lifetime. A predictive indoor environment monitoring system is designed based on a novel hybrid system to provide a nonstatic plan, approve energy consumption, and avoid failure of sensor nodes in a smart home.
This paper presents a compact broadband rectenna for harvesting RF energy in WLAN and WiMAX applications. A coplanar waveguide (CPW) rectangular monopole antenna loaded with double inverted-L strips is designed as the receiving antenna. By using an inverted-L open circuited stub as an input matching network, a compact rectifying circuit based on the voltage doubler principle is proposed, which has broadband performance. The receiving antenna and the rectifier are simulated using CST and ADS software packages, fabricated using photolithographic technique, and measured. The antenna is operating from 1.83-3.58 GHz (bandwidth of 1.75 GHz), and 5.4-6 GHz (bandwidth 600 MHz). These bands cover different wireless applications such as: GSM 1800, UMTS 2100, IEEE 802.11b&g WLAN systems, 3.5 GHz WiMAX system, and the IEEE 802.11a WLAN system. The antenna gain reaches 4.2 dBi at 5.8 GHz while the radiation efficiency is 99.6 %. The measured rectifier conversion efficiency reaches 29.72 % at 6 dBm input power while the measured total rectenna power conversion efficiency is 27.725 % at a frequency of 3.5 GHz.
This paper presents a 1 × 4 linear antenna array working at 28 GHz for 5G communication systems. The proposed array employs four rectangular slotted antenna elements fed by a 1 × 4 T-power divider. An artificial magnetic conductor (AMC) layer is placed below the array for increasing the radiation intensity and improving overall array gain. The measured impedance bandwidth of the proposed array with (|S11| < −10 dB) is extended from 25.36 to 26.03 GHz (with a bandwidth of 0.67 GHz) and from 26.75 to 28.81 GHz (with a bandwidth of 2.06 GHz). The proposed array design exhibits a measured gain value that varies between 11.8 dBi and 13.1 dBi within the operating bands and reaches 13.1 dBi at 28 GHz. The proposed array achieves a radiation efficiency of 83.05%, and a front-to-back ratio ranging between 15 and 20 dB across the operating frequency band. The array is fabricated and tested with good matching between the simulated and tested outcomes. The improved performance of the array makes it a suitable candidate for 5G new radio (NR) communications.
24 February 2021 in International Journal of RF and Microwave Computer-Aided Engineering
This article presents a single‐fed single‐layer dual‐band slotted antenna which has the ability to simultaneously operate at microwave and millimeter‐wave (MMW) frequency bands. It consists of a rectangular slotted ground plane, double cascaded tuning stubs, and embedded MMW element of L‐shape inside the slotted ground. Ultra‐wideband bandstop filter (BSF) is inserted at the feeding for isolating the two operational bands. The BSF consists of 3‐open circuited stubs and in‐line coupled line section. For demonstration, a design prototype of the complete integrated filtenna is fabricated and measured. Good agreements between simulated and measured results are observed. The proposed filtenna operates at 5.2 and 28 GHz with impedance bandwidth (15.23% and 17.03%) and the gain reaches (4.09 and 6.18 dBi).