To obtain a nanocrystalline SnO2 matrix and mono- and bimetallic nanocomposites SnO2/Pd, SnO2/Pt, and SnO2/PtPd, a flame spray pyrolysis with subsequent impregnation was used. The materials were characterized using X-ray diffraction (XRD), a single-point BET method, transmission electron microscopy (TEM), and high angle annular dark field scanning transmission electron microscopy (HAADF-STEM) with energy dispersive X-ray (EDX) mapping. The electronic state of the metals in mono- and bimetallic clusters was determined using X-ray photoelectron spectroscopy (XPS). The active surface sites were investigated using the Fourier Transform infrared spectroscopy (FTIR) and thermo-programmed reduction with hydrogen (TPR-H2) methods. The sensor response of blank SnO2 and nanocomposites had a carbon monoxide (CO) level of 6.7 ppm and was determined in the temperature range 60–300 °C in dry (Relative Humidity (RH) = 0%) and humid (RH = 20%) air. The sensor properties of the mono- and bimetallic nanocomposites were analyzed on the basis of information on the electronic state, the distribution of modifiers in SnO2 matrix, and active surface centers. For SnO2/PtPd, the combined effect of the modifiers on the electrophysical properties of SnO2 explained the inversion of sensor response from n- to p-types observed in dry conditions.
Photoactivation by UV and visible radiation is a promising approach for the development of semiconductor gas sensors with reduced power consumption, high sensitivity, and stability. Although many hopeful results were achieved in this direction, the theoretical basis for the processes responsible for the photoactivated gas sensitivity still needs to be clarified. In this work, we investigated the mechanisms of UV-activated processes on the surface of nanocrystalline ZnO, In2O3, and SnO2 by in situ mass spectrometry and compared the obtained results with the gas sensitivity to oxygen in the dark and at UV irradiation. The results revealed a correlation between the photoactivated oxygen isotopic exchange activity and UV-activated oxygen gas sensitivity of the studied metal oxides. To interpret the data obtained, a model was proposed based on the idea of the generation of additional oxygen vacancies under UV irradiation due to the interaction with photoexcited holes.
In this work, the photostimulated processes of O2 and NO2 molecules with the surface of ZnO under UV radiation were studied by in situ mass spectrometry in the temperature range of 30–100 C. Nanocrystalline needle-like ZnO was synthesized by decomposition of basic zinc carbonate at 300 C, and the surface concentration of oxygen vacancies in it were controlled by reductive post-annealing in an inert gas at 170 C. The synthesized materials were characterized by XRD, SEM, low-temperature nitrogen adsorption (BET), XPS, Raman spectroscopy, and PL spectroscopy. Irradiation of samples with UV light causes the photoabsorption of both O2 and NO2. The photoadsorption properties of ZnO are compared with its defective structure and gas-sensitive properties to NO2. A model of the sensor response of ZnO to NO2 under UV photoactivation is proposed.
In recent years, wide bandgap metal oxide semiconductors have become the base materials of choice for semiconductor gas sensor design. In this work, nanocrystalline ZnO, In2O3, and SnO2 were investigated when detecting NO2 under UV-photoactivation conditions. The materials were characterized by XRD, low-temperature nitrogen adsorption, and electron microscopy. The article considers the mechanism of sensor signal formation, as well as the mechanism of action of UV-light photoactivation, using an in situ multi-method approach. In situ mass spectrometry and in situ TR-DRIFTS were employed to study the impact of UV-light photoactivation on target gas adsorption equilibrium as well as the electrical and gas-sensing properties of the materials.
Zinc oxide is one of the well-known photocatalysts, the potential applications of which are of great importance in photoactivated gas sensing, water and air purification, photocatalytic synthesis, among others. However, the photocatalytic performance of ZnO strongly depends on its morphology, composition of impurities, defect structure, and other parameters. In this paper, we present a route for the synthesis of highly active nanocrystalline ZnO using commercial ZnO micropowder and ammonium bicarbonate as starting precursors in aqueous solutions under mild conditions. As an intermediate product, hydrozincite is formed with a unique morphology of nanoplates with a thickness of about 14–15 nm, the thermal decomposition of which leads to the formation of uniform ZnO nanocrystals with an average size of 10–16 nm. The synthesized highly active ZnO powder has a mesoporous structure with a BET surface area of 79.5 ± 4.0 , an average pore size of 20 ± 2 nm, and a cumulative pore volume of 0.507 ± 0.051 . The defect-related PL of the synthesized ZnO is represented by a broad band with a maximum at 575 nm. The crystal structure, Raman spectra, morphology, atomic charge state, and optical and photoluminescence properties of the synthesized compounds are also discussed. The photo-oxidation of acetone vapor over ZnO is studied by in situ mass spectrometry at room temperature and UV irradiation ( = 365 nm). The main products of the acetone photo-oxidation reaction, water and carbon dioxide, are detected by mass spectrometry, and the kinetics of their release under irradiation are studied. The effect of morphology and microstructure on the photo-oxidative activity of ZnO samples is demonstrated.
Inductively coupled plasma mass spectrometry (ICP-MS) is used for separate determination of platinum and palladium on the surface and in the bulk of nanocomposites based on tin dioxide. Synthesis of SnO2 matrices was conducted using deposition from solution and flame spray pyrolysis (FSP). The modifiers were injected by impregnation via the dispersion of the matrix powders in the solutions of precursors in volatile solvents and subsequent evaporation of the solvent. It is shown that palladium is present on the surface of the nanocomposites regardless of the synthesis procedure. As losses of the modifier after impregnation of SnO2 synthesized by the FSP method are observed, we conclude that the properties of the SnO2 surface depend on the method of obtaining the matrix. It is also shown that, for the materials obtained by the method of deposition from the solutions, 30–50% of Pt is present on the surface and other 50–70% is distributed in the bulk of SnO2. The use of flame spray pyrolysis makes it possible to increase the content of Pt on the surface up to 80%. The loss of Pt observed in both cases and attributed to the differences in the microstructure of SnO2 results in the etherification of thin layers of phases of complex composition which affect the processes of superficial diffusion and evaporation. Reproducibility of the results of Pt and Pd determination indicates a high degree of heterogeneity of the studied materials.