Pengfei Yan

Dr. Pengfei Yan

Tongji University

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 September 2018 in Metals
Verified
Journal Article
Open access
PDF file
YXYuye Xie
Yuye Xie
PYPengfei Yan
Pengfei Yan
BYBiao Yan
Biao Yan
An iron-based soft magnetic composite with Fe3O4-MnZnFe2O4 insulation coating has been prepared by powder metallurgy method. This work investigated the microstructure and magnetic properties of Fe/Fe3O4-MnZnFe2O4 powder cores. Scanning electron microscopy (SEM) coupled with an energy dispersive spectrometry (EDS) analysis indicated that the Fe3O4 and MnZnFe2O4 nanoparticles were uniformly coated on the surface of Fe powders. The co-existence of Fe3O4 and MnZnFe2O4 contributes to the preferable distribution of nano-sized insulation powders and excellent soft magnetic properties of soft magnetic composite (SMC) with high saturation magnetization Ms (215 A·m2/kg), low core loss (178.7 W/kg measured at 100 kHz, 50 mT), and high effective amplitude permeability of 114 (measured at 100 kHz). Overall, this work has great potential for realizing low core loss and outstanding soft magnetic properties of Fe-based powder cores.

26 October 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
ZLZhehao Lu
Zhehao Lu
WYWenyuan Yan
Wenyuan Yan
PYPengfei Yan
Pengfei Yan
BYBiao Yan
Biao Yan
The objective of the study is to investigate the strengthening mechanism of embedded meta-precipitates in the design of architected metamaterials. Four precipitate-type architected metamaterials are designed and prepared by fused deposition modelling (FDM). The difference of mechanical properties and deformation mode of these structures is analyzed. The strengthening effect of the introduced meta-precipitates is then compared with Orowan bypass strengthening mechanism. The similarities and discrepancies of metallurgical hardening principles and that found in architected metamaterials are established. It is found that due to the introduction of embedded meta-precipitates, the deformation of the structure changes significantly from diagonal crushing to a meander route, thus improves the mechanical properties and energy absorption abilities. The hindering effect and the influence of volume fraction of meta-precipitates is similar to Orowan bypass mechanism.

24 March 2021 in Metals
Verified
Journal Article
Open access
PDF file
CYChunyue Yin
Chunyue Yin
ZLZhehao Lu
Zhehao Lu
XWXianshun Wei
Xianshun Wei
BYBiao Yan
Biao Yan
PYPengfei Yan
Pengfei Yan
The objective of the study is to investigate the corresponding microstructure and mechanical properties, especially bending strength, of the hypereutectic Al-Si alloy processed by selective laser melting (SLM). Almost dense Al-22Si-0.2Fe-0.1Cu-Re alloy is fabricated from a novel type of powder materials with optimized processing parameters. Phase analysis of such Al-22Si-0.2Fe-0.1Cu-Re alloy shows that the solubility of Si in Al matrix increases significantly. The fine microstructure can be observed, divided into three zones: fine zones, coarse zones, and heat-affected zones (HAZs). Fine zones are directly generated from the liquid phase with the characteristic of petaloid structures and bulk Al-Si eutectic. Due to the fine microstructure induced by the rapid cooling rate of SLM, the primary silicon presents a minimum average size of ~0.5 μm in fine zones, significantly smaller than that in the conventional produced hypereutectic samples. Moreover, the maximum value of Vickers hardness reaches ~170 HV0.2, and bending strength increases to 687.70 MPa for the as-built Al-22Si-0.2Fe-0.1Cu-Re alloys parts, which is much higher than that of cast counterparts. The formation mechanism of this fine microstructure and the enhancement reasons of bending strength are also discussed.

1 September 2019 in Materials Research Express
Verified
Journal Article
Closed access
PDF file
QGQin Guihong
Qin Guihong
JHJiang Haojie
Jiang Haojie
YBYan Biao
Yan Biao
PYPengfei Yan
Pengfei Yan
Deformation behavior of Ti-6Al-6V-2Sn alloy possessing an equiaxed α-β preform microstructure was theoretically simulated at a temperature of 800-920 ℃ and at a strain rate of 0.01-10 s-1 for the purpose of analyzing its processing window and microstructure evolution during hot processing. As temperature increased, flow stress decreased when alloy samples were deformed at a fixed strain rate. Softening behavior can be observed at lower temperatures at all strain rates, which can possibly be explained by the dynamic recrystallization (DRX) of the lamellar α-phase. Alloy microstructure did not change significantly during deformations when the temperature is lower than 830 ºC. Thus, the microstructure evolution of Ti-6Al-6V-2Sn alloy could only be quantitatively described under such conditions. For deformations occurring in the range of 830-860 ℃, α-polymorph formed spherical clusters, whereas β-polymorph underwent DRX. With regard to temperature above 860 ℃, content of the initially major α-phase declined rapidly. Meanwhile, content of the secondary acicular martensite α'-phase rose up, and grains of the β-polymorph became larger. At strain rate equals to 0.1 s-1, flow stress peak was not able to be observed at the initial stage. When it finally became detectible, the value of the flow stress peak first went up and then gradually fell down. Such behavior was attributed to the formation of three different phases at a certain condition (α-Ti, β-Ti and α''-Ti). Optimum hot deformation conditions of Ti-6Al-6V-2Sn determined from the processing map were in the temperature range of 887-920 ℃ and at 0.01-0.75 s-1 strain rates.

27 October 2022 in Metals
Verified
Journal Article
Open access
PDF file
JZJizhe Zhang
Jizhe Zhang
PYPengfei Yan
Pengfei Yan
BYBiao Yan
Biao Yan
In this study, Cu and Ni are successfully added to additively manufactured Al-Si alloy by the mixing process to improve the strength and ductility of the alloy. The effects of different heat treatments on the microstructural evolution and bending properties of selective laser-melted Al-Si-Cu-Ni-Fe-Re alloy are systematically investigated to optimize the mechanical properties. Nearly complete dense samples are initially additively manufactured with optimized parameters. The samples display a particular fiber network microstructure in which Cu-rich and Ni-rich phases distribute in an interwoven mesh around the eutectic silicon. After substrate plate heating (SPH) treatment, the network becomes denser, and the bending strength increases by 44.99 ± 1 MPa to 811.11 ± 29 MPa, despite the hardness decreases. Comparatively, solution aging (SQA) treatment results in the fiber network structures transforming into second-phase particles, which leads to a decline in bending strength and a significantly higher degree of ductility. Finally, the mechanisms of changes in microstructure and morphology, as well as mechanical properties after heat treatment, are discussed.