N-Doped few-layer graphene encapsulated Pt-based bimetallic nanoparticles were successfully synthesized via the solution plasma (SP) method. This synthesis strategy can be achieved in one pot by using only pure dimethylformamide (DMF) as the reaction solution at room temperature and atmospheric pressure. The structural analyses exhibited a fine core–shell structured nanoparticle (2–4 nm), which had Pt and Pt-based bimetallic nanoparticles as a core and N-doped few-layer graphene (NFG), having 2–4 layers, as a shell. Pt-based bimetallic cores (i.e., PtAu, PtAg, and PtPd) were varied depending on the metal electrodes used in the SP process. The electrocatalytic activity toward the oxygen reduction reaction (ORR) of the obtained samples in an acidic solution was found to be acceptable, while possessing excellent durability, compared to those of the commercial carbon-supported Pt catalyst. The effective ORR activity was possibly attributed to the synergistic effect of the Pt-based bimetallic core and N-doped graphene shell which contained high amounts of pyridinic-N and quaternary-N. The results in a single fuel cell test expressed the superiority of our SP-derived sample in the fuel cell performances to commercial Pt/C. This study not only proposed potential alternative ORR catalysts with acceptable electrocatalytic activity and high durability but also provided guidelines for the facile synthesis of carbon-based core–shell nanostructured materials with low chemical use via the SP process.
The reinforcement of filler materials into an unsaturated polyester (UPE) matrix is often limited by agglomeration, leading to poor compatibility. Recently, nano-sized filler materials have attracted attention as effective reinforcement agents in UPE. In this study, styrene polymer-grafted carbon nanoparticles were synthesized using the solution plasma method and applied as reinforcing additives for UPE. The synthesis of nanoparticles was conducted directly in the styrene monomer environment, enabling the simultaneous formation of carbon nanoparticles and the grafting of polymer onto their surfaces via a free-radical mechanism. SEM analysis revealed more uniform particle dispersion and a polymer-coated surface in UPE/NC-gP samples, indicating increased compatibility with the matrix. FTIR also showed that the representative peaks C–H, CC, CO, and C–O oscillated clearly in the UPE/NC-gP samples. Notably, the use of styrene-grafted carbon nanoparticle significantly improved the tensile modulus, tensile strength, flexural modulus, and flexural strength of the UPE/NC-gP(1 h) sample to 479.89 ± 26.22, 39.23 ± 2.06, 1504.06 ± 55.18, and 44.67 ± 1.82 MPa, respectively, compared with UPE/SM. Meanwhile, the UPE/NC-gP(3 h) sample had the highest flexural stress and flexural modulus of 49.01 ± 3.03 and 1535.81 ± 58.47 MPa, respectively, but the flexural strain was low. The results indicate that the grafting time influences the properties of the UPE composite. This study confirms the potential of the solution plasma method for the fabrication of nanoadditives highly compatible with the polymer matrix, opening new avenues for the production of nanocomposite materials.
The growing demand for electronic storage devices with faster charging rates, higher energy capacities, and longer cycle lives has led to significant advancements in supercapacitor technology. These devices typically utilize high-surface-area carbon-based materials as electrodes, which provide excellent power densities and cycling stability. However, challenges such as inadequate electrolyte interaction, hydrophobicity that impedes ion transport, and high manufacturing costs restrict their effectiveness. This study aims to enhance carbon-based materials by grafting polymer chains onto their surfaces for supercapacitor applications. A simple solution plasma process (SPP), followed by heating, prepared the polymer-grafted carbon materials. Carbon nanoparticles were synthesized from benzene through plasma discharge in liquid under ambient conditions, forming free radical sites on the carbon surface. Subsequently, benzene molecules were grafted onto the surface via radical polymerization during heating. We investigated the structural and morphological properties of the synthesized materials using scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR), X-ray powder diffraction (XRD), and Raman spectroscopy. Additionally, N2 absorption–desorption isotherms were measured, pore structure was analyzed with the Dubinin–Astakhov (DA) average pore size model, and specific surface area was determined using the Brunauer–Emmett–Teller (BET) equation for all synthesized samples. The results indicated that the grafting process was influenced by heating time and drying temperature. Furthermore, the electrical properties of the samples were evaluated using cyclic voltammetry (CV), which demonstrated enhancements in both areal capacitance and cycling stability for the polybenzene-grafted carbon compared to the non-grafted variant. This research illustrates that polymer grafting can effectively improve the performance and stability of carbon-based materials for supercapacitor applications. Future work will aim to optimize these materials for broader applications.
23 March 2018 in Vietnam Journal of Science and Technology
In this research, ethylene–propylene–diene (EPDM) rubber, a type of synthetic rubber with excellent anti–vibration and anti–noise properties, was studied for the application in anti–vibration pads. Via changes in the concentration of substances in the mixtures such as carbon black, triethanolamine (TEA) and sulfur, the mechanical properties and the anti–vibration efficiency of the EPDM rubber samples were determined using mechanical tester. As a result, the EPDM rubber samples containing about 45 % of carbon black N330, 1 % of TEA and 1 % of sulfur showed some good results including the shore hardness about 62 A, the compressive stress at peak of 1.04 N/mm2 and the anti–vibration efficiency approximately 72 %.