P S Satheesh Kumar

Dr. P S Satheesh Kumar

orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 October 2022 in Advances in Materials Science and Engineering
Verified
Journal Article
Open access
PDF file
VSvijayakumar Sivasundar
vijayakumar Sivasundar
P S Satheesh KumarP S Satheesh Kumar
P S Satheesh Kumar
SMSelvaraj Manickam
Selvaraj Manickam
GRGurumurthy B. Ramaiah
Gurumurthy B. Ramaiah
HPHari Prasadarao Pydi
Hari Prasadarao Pydi
This present investigation focusing on preparation of Al-based hybrid composites in which Al6082 is engaged as the main alloy reinforced with two reinforcements of ZrSiO/TiC. The combination of the stir-squeeze process helps to make different specimen by change of four parameters such as stir speed, stir time, reinforcements, and squeeze pressure. In this process, two reinforcements are reserved as constant about 7.5 wt. The four levels of each parameter are stir speed (300, 400, 500, and 600rpm), stir time (10, 15, 20, and 25min), reinforcement (2.5, 5, 7.5, and 10 wt), and squeeze pressure (50, 60,70, and 80MPa). According to the L16 orthogonal array Taguchi design, the specimens are created to analyze the mechanical properties of tensile strength and hardness along with porosity. In addition, the optimization technique is used to determine the optimal parameter on improving tensile strength. The optimization process can be assisted by the software namely Minitab-17 which helps to study analysis of variance, regression model, and contour plots. The observed result of ANOVA showed that stir speed (41.8) is the maximum influenced parameter that increases TS, followed by squeeze pressure (25.7), stir time (12.7), and reinforcement (1.96), and optimum tensile strength is found at the parameters of stir speed 600rpm, stir time 10min, reinforcement 2.5 wt, and squeeze pressure 80MPa. The fractured surface of tensile strength also examined by the SEM test. The combined parameters of S4-T1-R1-P4 achieve the highest TS, and it is observed that there are nearly no pore defects and good diffusion as a result of the reinforcements to be properly mixed. It is noticeable that the TiC and Al 6082 matrix, as well as the various ZrSiO4 exhibit stronger bonds.

1 January 2021 in Advances in Materials Science and Engineering
Verified
Journal Article
Open access
PDF file
Bhiksha GugulothuBhiksha Gugulothu
Bhiksha Gugulothu
P S Satheesh KumarP S Satheesh Kumar
P S Satheesh Kumar
BSBathula Srinivas
Bathula Srinivas
ARAlapati Ramakrishna
Alapati Ramakrishna
SVS. Vijayakumar
S. Vijayakumar
This study explained about machining parameters of Al5086/Flyash/Sic hybrid metal matrix composites by the Taguchi technique. Al5086 reinforced in SiC (5–10 wt %) and 8% weight of flyash are retained as constants. The specimens are prepared with the help of the stir casting method. The material removal rate was examined by electrochemical machining under various parameters such as feed rate (0.15–0.30 mm/min), voltage (10–20 V), and electrolyte concentration (20–35 g/litre). Taguchi’s L16 orthogonal array was selected for design of experiments (DOEs), and 16 experimental tests were conducted to examine the effect of the selected machining parameters employed to identify the best optimal levels and also to investigate the effect of electrochemical machining parameters on MRR determined by Minitab‐18.

1 March 2012 in Monthly Notices of the Royal Astronomical Society: Letters
Verified
Journal Article
Open access
Zeljka Marija BosnjakZeljka Marija Bosnjak
Zeljka Marija Bosnjak
P S Satheesh KumarP S Satheesh Kumar
P S Satheesh Kumar
Photons of energy larger than 100 MeV from long-GRBs arrive a few seconds after 100 MeV. The delay depends almost linearly on burst redshift, and on the distance from the central compact object where the jet is launched (R_0). Therefore, the delay in arrival of >10^2 MeV photons can be used to estimate burst redshift if the magnetic jet model for gamma-ray generation is correct and R_0 is roughly the same for long-GRBs.Comment: 5 pages; submitted to MNRA

25 August 2018 in Applied Physics A
Verified
Journal Article
Closed access
PDF file
SPS. Palanichamy
S. Palanichamy
JMJ. Raj Mohamed
J. Raj Mohamed
P S Satheesh KumarP S Satheesh Kumar
P S Satheesh Kumar
SPS. Pandiarajan
S. Pandiarajan
LAL. Amalraj
L. Amalraj

1 October 2019 in Optik
Verified
Journal Article
Closed access
PSPalanichamy S.
Palanichamy S.
RJRaj Mohamed J.
Raj Mohamed J.
DKDeva Arun Kumar K.
Deva Arun Kumar K.
P S Satheesh KumarP S Satheesh Kumar
P S Satheesh Kumar
PSPandiarajan S.
Pandiarajan S.
ALAmalraj L.
Amalraj L.

30 August 2018 in Optical and Quantum Electronics
Verified
Journal Article
Closed access
PDF file
SPS. Palanichamy
S. Palanichamy
JMJ. Raj Mohamed
J. Raj Mohamed
P S Satheesh KumarP S Satheesh Kumar
P S Satheesh Kumar
SPS. Pandiarajan
S. Pandiarajan
LAL. Amalraj
L. Amalraj