Nanoindentation is widely used to investigate the surface-mechanical properties of biocomposites. In this study, polypropylene random copolymer (PPRC) and biowaste rice husk (BRH) were used as the main raw materials, and glass-fiber-reinforced polypropylene and talc were also used with BRH to enhance the mechanical characterization of the biocomposites. The interfacial bonding between the polymer and the rice husk was increased by treating them with maleic anhydride and NaOH, respectively. The results obtained from the nanoindentation indicated that the plastic behavior of the biocomposites was prominent when untreated BRH was used and vice versa. The modulus and hardness of the biocomposite improved by 44.8% and 54.8% due to the neat PPRC, respectively. The tribological properties were studied based on the hardness-to-modulus ratio and it was found that BRH- and talc-based biocomposites were better than other samples in terms of low friction and wear rate. The creep measurements showed that untreated rice husk biocomposite exhibited high resistance to load deformation.
In this work, the effects of different fiber loadings on the mechanical properties of the composites at the sub-micron scale were studied through nanoindentation followed by physical characterization. The composites were prepared by incorporating different loadings of wheat straw, corn stalk, and rice husk in polypropylene copolymer using a melt processing method followed by thermal–hydraulic compression technique. Nanoindentation experiments in quasi-continuous stiffness mode were performed on the surfaces of produced composites to study the composites’ elastic modulus, hardness, and creep properties. The obtained results expressed the in-depth study of the micro- and macro-level structure and behavior of particle interactions. The findings demonstrated that observable shifts in composites’ hardness, elastic modulus, and creep rate had occurred. The WS-reinforced biocomposite sheet showed the highest elastic modulus of 1.09 and hardness of 0.11 GPa at 40 wt% loading in comparison to other loadings. An impact strength of 7.55 kJ/m2 was noted for the biocomposite at 40 wt% RH loading. In addition, optical microscopy, Fourier transform infrared spectroscopy, water absorption, thickness swelling, and Vicat softening point studies were conducted on biocomposite sheets to evaluate differences in physical, mechanical, and thermal properties. The outstanding mechanical performance of the newly developed composites makes them suitable for use as a biodegradable packaging material.
6 September 2026 in Journal of Composite Materials
Rice husk (RH) is one of the abundant lignocellulosic biowastes which can be used to reinforce recyclable thermoplastic matrices, but the contribution of rice husk to the surface performance is highly dependent on filler loading, pretreatment and inorganic co-filler dispersion. In this study, high loading RH or alkali treated RH (RHT) wood-polymer composite sheets (10 and 15 wt.%) with and without 2 wt.% talc are evaluated. FTIR was employed as a supplementary technique to verify the incorporation of RH and maleic-anhydride-assisted coupling, while FESEM and quasi-continuous stiffness nanoindentation provided the bulk of the structure-property analysis. Alkali treatment was found to open and fibrillate RH surfaces, while talc showed lamellar particles that could fill in local voids. Within the 2 3 factorial design space examined (10 or 15 wt.% rice husk, untreated or alkali-treated, with or without 2 wt.% talc), nanoindentation identified 10RHT as the best-performing formulation for contact stiffness (48.06 mN/µm), 15RHT/2%TLC for elastic modulus (1.78 GPa) and 10RH/2%TLC for indentation hardness (≈0.25 GPa). A first-order-plus-interaction model fitted to the eight formulations showed that talc content was the largest single contributor to indentation hardness and that the loading × treatment interaction exceeded either main effect. In addition, the use of treated systems with talc also reduced time-dependent creep deformation, which is a sign of increased resistance to localized contact loading for sustainable WPC applications.
28 September 2026 in Composites Part C: Open Access