This study examines the impact of mix design parameters on the environmental effects of producing concrete and reinforced concrete buildings by conducting a life cycle assessment (LCA) and carbon footprint analysis (CFA). The study is limited to the cradle-to-gate phase, including the extraction and production of raw materials for concrete production, as well as concrete and rebar production, material transportation, and delivery to the construction site for reinforced concrete structures. Three concrete mix designs based on the American Concrete Institute (ACI) 211-09 standard, with compressive strengths of 20, 30, and 40 MPa, were analyzed. The results indicate that cement was the primary contributor to environmental impacts, accounting for approximately 90% of the carbon footprint. Sand, gravel, and admixtures followed cement in their impact on LCA results. Water usage in concrete production had a negligible effect on LCA indicators. Moreover, to determine how mix design parameters impact the carbon footprint of reinforced concrete buildings, three four-story structures were designed. The results show that in reinforced concrete buildings, concrete was a significant contributor to environmental impacts, accounting for over 50% of all indicators in the IMPACT 2002+ and CML baseline 2000 methods, except for resources and acidification. The study underscores the importance of considering mix design parameters in reducing the carbon footprint of reinforced concrete buildings and provides valuable insights into their environmental impacts. The findings indicate that cement is the main driver of environmental impacts in both assessment methods, accounting for around 90% of the carbon footprint. Additionally, concrete plays a substantial role in environmental effects, contributing to over 50% of all indicators measured in the methods used for evaluating environmental impacts.

This study investigates the cracking behavior of high-performance calcium oxide-activated concrete incorporating basalt and synthetic macro fibers under compressive and flexural loading. Acoustic emission (AE) monitoring was employed to capture real-time crack initiation and propagation, offering insights into damage evolution mechanisms. A comprehensive series of uniaxial compression and four-point bending tests were conducted on fiber-reinforced and plain specimens. AE parameters, including count, duration, risetime, amplitude, and signal energy, were analyzed to quantify crack intensity and classify fracture modes. The results showed that tensile cracking dominated even under compressive loading due to lateral stresses, while fiber inclusion significantly enhanced toughness by promoting distributed microcracking and reducing abrupt energy release. Basalt fibers were particularly effective under flexural loading, increasing the post-peak load-bearing capacity, whereas synthetic macro fibers excelled in minimizing tensile crack occurrence under compression.

This study explores a sustainable strategy for enhancing high-strength concrete (HSC) by partially replacing natural fine aggregates with stone quarry sludge (SQS), a byproduct of quarrying operations. The aim is to promote environmental conservation and waste valorization while maintaining or improving concrete performance. Concrete mixes were prepared by substituting fine sand with SQS at incremental levels of 10%, 20%, 30%, 40%, and 50%. Mechanical properties were assessed through specific weight measurements, compressive strength tests, and three-point bending evaluations. FTIR analysis was conducted to investigate microstructural changes, and a carbon footprint assessment was performed to quantify environmental benefits. The mix containing 20% SQS exhibited optimal performance, achieving a compressive strength of 61 MPa and a bending strength of 5.1 MPa. FTIR results confirmed enhanced C–S–H gel formation, indicating improved microstructural integrity. Carbon footprint analysis revealed that moderate SQS substitution significantly reduces embodied carbon. These findings support the use of quarry sludge as a viable component in eco-friendly HSC, with potential for further optimization and long-term durability studies.

Joints, which are usually located in the abutments of dams, play a vital role in the seismic stability evaluation of arch dams. This paper presents a comprehensive numerical investigation of the influence of uplift pressure in joints on the seismic response of an arch dam, with a focus on the interaction between the dam and the rock wedges. For this study, the Bakhtiari arch dam, having one rock wedge at each abutment, was chosen as a case study, and three distinct finite element models of the dam were developed. Three components of El Centro were applied to the dam's foundation, and the influences of dam-rock wedge interaction on the crest displacement time history and tensile damage of the arch dam were investigated. Four different scenarios were taken into account. The results indicated that taking uplift pressure in joints into account has important effects on the dam responsesWedge;Arch dam.