Predictive computational modeling of polymer materials is necessary for the efficient design of composite materials and the corresponding processing methods. Molecular dynamics (MD) modeling is especially important for establishing accurate processing–structure–property relationships for neat resins. For MD modeling of amorphous polymer materials, an accurate force field is fundamental to reliable prediction of properties. Reactive force fields, in which chemical bonds can be formed or broken, offer further capability in predicting the mechanical behavior of amorphous polymers subjected to relatively large deformations. To this end, the reactive interface force field (IFF-R) has been recently developed to provide an efficient means to predict the behavior of materials under these conditions. Although IFF-R has been proven to be consistent for some crystalline organic and inorganic systems, it has not yet been proven to be consistent for amorphous polymer systems. The objective of this study is to use IFF-R to predict the thermomechanical properties of three different epoxy systems and validate them with experimental measurements. The results indicate that IFF-R predicts thermomechanical properties that are consistent with the experiment. Therefore, IFF-R can be used to reliably establish the mechanical properties of polymers on the molecular level for future design of new composite materials and processing methods.
Epoxy resins are used extensively in composite materials for a wide range of engineering applications, including structural components of aircraft and spacecraft. The processing of fiber-reinforced epoxy composite structures requires carefully selected heating and cooling cycles to fully cure the resin and form strong cross-linked networks. To fully optimize the processing parameters for effective epoxy monomer cross-linking and final product integrity, the evolution of mechanical properties of epoxies during processing must be comprehensively understood. Because the full experimental characterization of these properties as a function of degree of cure is difficult and time-consuming, efficient computational predictive tools are needed. The objective of this research is to develop an experimentally validated Molecular Dynamics (MD) modeling method, which incorporates a reactive force field, to accurately predict the thermo-mechanical properties of an epoxy resin as a function of the degree of cure. Experimental rheometric and mechanical testing are used to validate an MD model, which is subsequently used to predict mass density, shrinkage, elastic properties, and yield strength as a function of the degree of cure. The results indicate that each of the physical and mechanical properties evolve uniquely during the cross-linking process. These results are important for future processing modeling efforts.
The effect of residual stress build-up on the transverse properties of thermoset composites is studied through direct and inverse process modeling approaches. Progressive damage analysis is implemented to characterize composite stiffness and strength of cured composites microstructures. A size effect study is proposed to define the appropriate dimensions of Representative Volume Elements (RVEs). A comparison between periodic (PBCs) and flat (FBCs) boundary conditions during curing is performed on converged RVEs to establish computationally efficient methodologies. Transverse properties are analyzed as a function of the fiber packing through the nearest fiber distance statistical descriptor. A reasonable mechanical equivalence is achieved for RVEs consisting of 40 fibers. It has been found that process-induced residual stresses and fiber packing significantly contribute to the scatter in composites transverse strength. Variation of ±5% in average strength and 18% in standard deviation are observed with respect to ideally cured RVEs that neglect residual stresses. It is established that process modeling is needed to optimize the residual stress state and improve composite performance.
To enable the design and development of the next generation of high-performance composite materials, there is a need to establish improved computational simulation protocols for accurate and efficient prediction of physical, mechanical, and thermal properties of thermoset resins. This is especially true for the prediction of glass transition temperature (Tg), as there are many discrepancies in the literature regarding simulation protocols and the use of cooling rate correction factors for predicting values using molecular dynamics (MD) simulation. The objectives of this study are to demonstrate accurate prediction the Tg with MD without the use of cooling rate correction factors and to establish the influence of simulated conformational state and heating/cooling cycles on physical, mechanical, and thermal properties predicted with MD. The experimentally-validated MD results indicate that accurate predictions of Tg, elastic modulus, strength, and coefficient of thermal expansion are highly reliant upon establishing MD models with mass densities that match experiment within 2%. The results also indicate the cooling rate correction factors, model building within different conformational states, and the choice of heating/cooling simulation runs do not provide statistically significant differences in the accurate prediction of Tg values, given the typical scatter observed in MD predictions of amorphous polymer properties.
24 July 2023 in Composites Part A: Applied Science and Manufacturing