In this study, an experimental investigation of separation control using a dielectric barrier discharge plasma actuator was performed on an NACA0015 airfoil over a wide range of Reynolds numbers, angles of attack, and nondimensional burst frequencies. The range of the Reynolds number was based on a chord length ranging from 2.52 × 10 to 1.008 × 10. A plasma actuator was installed at the leading edge and driven by AC voltage. Burst mode (duty-cycle) actuation was applied, with the nondimensional burst frequency ranging between 0.1–30. The control authority was evaluated using the time-averaged distribution of the pressure coefficient and the calculated value of the lift coefficient . The baseline flow fields were classified into three types: (1) leading-edge separation; (2) trailing-edge separation; and (3) the hysteresis between (1) and (2). The results of the actuated cases show that the control trends clearly depend on the differences in the separation conditions. In leading-edge separation, actuation with a burst frequency of approximately 0.5 creates a wide negative pressure region on the suction-side surface, leading to an increase in the lift coefficient. In trailing-edge separation, several actuations alter the position of turbulent separation.
The flow control capability (especially for separation control) of a dielectric-barrier-discharge plasma actuator (DBD-PA) has been investigated extensively. However, these studies have been conducted under ideal conditions, such as wind tunnels and computational environments, and limited studies have investigated the effects of plasma actuators in an actual environment. In this study, the flow control capability of a DBD-PA under natural and in-flight conditions was investigated via field flight tests using an unmanned aerial vehicle (UAV). The DBD-PA driving system was constructed with a small high-voltage power supply on a 2-m-span UAV. With the support of an autonomous flight system, the pitch angle gradually increased as the airspeed decreased, and the stall occurred from the cruise state. This flight procedure was conducted with the DBD-PA on or off, and 246 pairs of flights were operated. The results revealed that a flight state with a higher pitch angle and lower airspeed occurred when DBD-PA was switched on. In addition, the moment of stall was quantitatively determined from the flight log, and it was confirmed that the maximum pitch angle when DBD-PA was switched on tended to be larger than that when DBD-PA was switched off. These results indicate that flow control with a DBD-PA on a 2-m-span UAV was effective in natural and in-flight situations.
A computational study was conducted on flows over an NACA0015 airfoil with dielectric barrier discharge (DBD) plasma. The separated flows were controlled by a DBD plasma actuator installed at the 5% chord position from the leading edge, where operated AC voltage was modulated with the duty cycle not given a priori but dynamically changed based on the flow fluctuations over the airfoil surface. A single-point pressure sensor was installed at the 40% chord position of the airfoil surface and the DBD plasma actuator was activated and deactivated based on the strength of the measured pressure fluctuations. The Reynolds number was set to 63,000 and flows at angles of attack of 12 and 16 degrees were considered. The three-dimensional compressible Navier–Stokes equations including the DBD plasma actuator body force were solved using an implicit large-eddy simulation. Good flow control was observed, and the burst frequency proven to be effective in previous fixed burst frequency studies is automatically realized by this approach. The burst frequency is related to the characteristic pressure fluctuation; our approach was improved based on the findings. This improved approach realizes the effective burst frequency with a lower control cost and is robust to changing the angle of attack.
1 January 2024 in The Journal of the Acoustical Society of America
This study experimentally investigated acoustically driven gas-mixture separation. Acoustic wave propagation in a narrow tube can induce gas-mixture separation. A binary mixture of helium and argon was used as the gas mixture. The pressure amplitude of the acoustic wave and initial molar fraction of the helium gas were investigated. The obtained experimental data indicated that the molar fraction initially increased with increasing pressure amplitude, whereas the saturated molar fraction did not show a clear dependence on the pressure. Although the degree of separation was smaller with purer helium, gas-mixture separation occurred under all conditions within the experimental range.
1 January 2015 in The Proceedings of Mechanical Engineering Congress, Japan
The present study focuses on the multiple separation-control mechanisms of burst actuation with a dielectric barrier discharge plasma actuator. Control of separated flow around a NACA 0015 airfoil at the Reynolds number of 63,000 is investigated using a plasma actuator mounted at 5% chord length from the leading edge. A parametric study on burst frequency and input voltage are conducted on three post-stall angles of attack using time-averaged pressure measurements and time-resolved particle imaging velocimetry (PIV). The trailing edge pressure is chosen as the index of separation control and indicates that the optimum burst frequency is different for each angle of attack. Several flow fields are discussed in detail and two flow-control mechanisms are clarified: the utilization of a large vortex and promotion of turbulent transition. With regard to the first mechanism, the phase-lock PIV indicates that a vortex structure, the size of which increases as the burst frequency decreases in this experimental range, is shed from the shear layer for each burst actuation. With regard to the second mechanism, time-averaged pressure and PIV measurements reveal that burst frequency of F^+ = 6-10 has the capability to promote turbulent transition. At higher angle of attack, only the utilization of a large vortex structure is effective for separation control, whereas, near the stall angle, the promotion of turbulent transition provides better separation control.