3D CFD analyses are used to analyse the effects of port-injection of water in a high performance turbocharged GDI engine. Particularly, water injection is adopted to replace mixture enrichment while preserving, if not improving, indicated mean effective pressure and knock resistance. A full-load / maximum power engine operation of a currently made turbocharged GDI engine is investigated comparing the actual adopted fuel-only rich mixture to stoichiometric-to-lean mixtures, for which water is added in the intake port under constant charge cooling in the combustion chamber. In order to find the optimum fuel/water balance, preliminary analyses are carried out using a chemical reactor to evaluate the effects of charge dilution and mixture modification on both autoignition delays and laminar flame speeds. Thanks to the lower chemical reactivity of the diluted end gases, the water-injected engine allows the spark advance (SA) to be increased; as a consequence, engine power target is met, or even crossed, with a simultaneous relevant reduction of fuel consumption

Engine downsizing is gaining popularity in the high performance engine market sector, where a new generation of highly downsized engines with specific power outputs around or above 150 HP/litre is emerging. High-boost and downsizing, adopted to increase power density and reduce fuel consumption, have to face the increased risks of pre-ignition, knock or mega-knock. To counterbalance autoignition of fuel/air mixture, such engines usually operate with high fuel enrichments and delayed (sometimes negative) spark advances. The former is responsible for high fuel consumption levels, while the latter reduces performance and induces an even lower A/F ratio (below 11), to limit the turbine inlet temperature, with huge negative effects on BSFC. A relatively simple yet effective solution to increase knock resistance is investigated by means of 3-D CFD analyses in the paper: water is port injected to replace mixture enrichment while preserving, if not improving, indicated mean effective pressure and knock safety margins. Full-load engine operations of a currently made turbocharged GDI engine are investigated comparing the adopted fuel-only rich mixture with stoichiometric mixtures, for which water is added in the intake port under constant charge cooling in the combustion chamber. In order to find the optimum fuel/water balance, preliminary analyses are carried out using a chemical reactor to evaluate the effects of charge dilution and mixture modification on both autoignition delays and laminar flame speeds. Thanks to the lower chemical reactivity of the diluted end gases, the water-injected engine allows the Spark Advance (SA) to be increased; as a consequence, engine power target is met, or even crossed, with a simultaneous relevant reduction of fuel consumption.

A new generation of highly downsized SI engines with specific power output around or above 150 HP/liter is emerging in the sport car market sector. Technologies such as high-boosting, direct injection and downsizing are adopted to increase power density and reduce fuel consumption. To counterbalance the increased risks of pre-ignition, knock or mega-knock, currently made turbocharged SI engines usually operate with high fuel enrichments and delayed (sometimes negative) spark advances. The former is responsible for high fuel consumption levels, while the latter induce an even lower A/F ratio (below 11), to limit the turbine inlet temperature, with huge negative effects on BSFC.A possible solution to increase knock resistance is investigated in the paper by means of 3D-CFD analyses: water/methanol emulsion is port-fuel injected to replace mixture enrichment while preserving, if not improving, indicated mean effective pressure and knock safety margins. The peak power engine operation of a currently made turbocharged GDI engine is investigated comparing the adopted fuel-only rich mixture with stoichiometric-to-lean mixtures, for which water/methanol mixture is added in the intake port under constant charge cooling in the combustion chamber and same air consumption level. In order to find the optimum fuel/emulsion balance analytic considerations are carried out. Different strategies are evaluated in terms of percentage of methanol-water emulsion rate, to assess the effects of different charge dilutions and mixture compositions on knock tendency and combustion efficiency. Thanks to the lower chemical reactivity of the diluted end gases and the faster burn rate allowed by the methanol addition, the water/methanol-injected engine allows the spark advance (SA) to be increased; as a consequence, engine power target is met, or even crossed, with a simultaneous relevant reduction of fuel consumption.

The paper reports an activity aiming at characterizing cycle-to-cycle variability (CCV) of the spark-ignition (SI) process in a high performance engine. The numerical simulation of spark-ignition and of early flame kernel evolution are major challenges, mainly due to the time scales of the spark discharge process and to the reduced spatial scales of flame kernel. Typical mesh resolutions are insufficient to resolve the process and a dedicated treatment has to be provided at a subgrid level if the ignition process is to be properly modelled. The focus of this work is on the recent ISSIM-LES (Imposed Stretch Spark-Ignition Model) ignition model, which is based on an extension of the flame surface density (FSD) transport equation for a dedicated flame kernel treatment at subgrid scales. The FSD equation is solved immediately after spark discharge. The interaction of the flame kernel with the flow field is fully accounted for since spark formation and a transition is provided from ignition to propagation phase. The comparison is carried out with the AKTIM-Euler ignition model in terms of flame interaction with the flow field (e.g. arc convection, flame blow-off, flame holder effect). A multiple cycle LES activity provided a set of cycle-resolved conditions for spark-ignition comparisons, and the flame kernel development is carefully analyzed for the two ignition models on a wide range of thermo-physical conditions. Spark-ignition cyclic variability and combustion traces are compared with experiments. Results confirm that the simulated cycle-to-cycle variability increases through the adoption of the ISSIM-LES ignition model.

The recent rise in fuel prices, the need both to reduce ground transport-generated emissions (increasingly constrained by legislation) and to improve urban air quality have brought fuel-efficient, low-emissions powertrain technologies at the top of vehicle manufacturers’ and policy makers’ agenda. To these aims, engine design is now oriented towards the adoption of the so-called downsizing and down-speeding techniques, while preserving the performance target. Therefore, brake mean effective pressure is markedly increasing, leading to increased risks of knock onset and abnormal combustions in last-generation SI engines. To counterbalance the increased risks of pre-ignition, knock or mega-knock, currently made turbocharged SI engines usually operate with high fuel enrichments and delayed (sometimes negative) spark advances. The former is responsible for high fuel consumption levels, while the latter induce an even lower A/F ratio (below 11), to limit the turbine inlet temperature, with huge negative effects on BSFC. Possible solutions to increase knock resistance are investigated in the paper by means of 3D-CFD analyses: water, water/methanol emulsion and methanol are port-fuel injected to replace mixture enrichment while preserving, if not improving, indicated mean effective pressure and knock safety margins. The aim of the work is therefore the replacement of the gasoline-only rich mixture with a global stoichiometric one while avoiding power loss and improving fuel consumption. In order to maintain the same knock tendency, water, methanol or a mixture of the two is then added in the intake port to keep the same charge cooling of the original rich mixture. Different strategies in terms of methanol/water ratios of the port injected mixture are compared in order to find the best trade-off between fuel consumption, performance and knock tendency