Seok-Ho Rhi

Prof. Dr. Seok-Ho Rhi

School of Mechanical Engineering, Chungbuk National University, Cheongju-si, Republic of Korea
orcid

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 March 2011 in Journal of Electronic Materials
Verified
Journal Article
Closed access
PDF file
SKSun-Kook Kim
Sun-Kook Kim
BWByeong-Cheol Won
Byeong-Cheol Won
Seok-Ho RhiSeok-Ho Rhi
Seok-Ho Rhi
SKShi-Ho Kim
Shi-Ho Kim
JYJeong-Ho Yoo
Jeong-Ho Yoo
JJJu-Chan Jang
Ju-Chan Jang

15 March 2018 in Energies
Verified
Journal Article
Open access
PDF file
CRCHI RIGUANG
CHI RIGUANG
WCWon-Sik Chung
Won-Sik Chung
Seok-Ho RhiSeok-Ho Rhi
Seok-Ho Rhi
The heat generation of lithium ion batteries in electric vehicles (EVs) leads to a degradation of energy capacity and lifetime. To solve this problem, a new cooling concept using an oscillating heat pipe (OHP) is proposed. In the present study, an OHP has been adopted for Li-ion battery cooling. Due to the limited space in EVs, the cooling channel is installed on the bottom of the battery module. In the bottom cooling method with an OHP, generated heat can be dissipated easily and conveniently. However, most studies on heat pipes have used bottom heating and top or side cooling methods, so we investigate the various effects of parameters with a top heating/bottom cooling mode with the OHP, i.e., the inclination angle of the system, amount of working fluid charged, the heating amount, and the cold plate temperature with ethanol as a working fluid. The experimental results show that the thermal resistance (0.6 °C/W) and uneven pulsating features influence the heat transfer performance. A heater used as a simulated battery was sustained under 60 °C under 10 W and 14 W heating conditions. This indicates that the proposed cooling system with the bottom cooling is feasible for use as an EV’s battery cooling system.

5 May 2019 in Energies
Verified
Journal Article
Open access
PDF file
CRCHI RIGUANG
CHI RIGUANG
Seok-Ho RhiSeok-Ho Rhi
Seok-Ho Rhi
Recently, the use of electrical vehicles has abruptly increased due to environmental crises. The high energy density of lithium-ion batteries is their main advantage for use in electric vehicles (EVs). However, the thermal management of Li-ion batteries is a challenge due to the poor heat resistance of Lithium ions. The performance and lifetime of lithium ion batteries are strongly affected by the internal operating temperature. Thermal characterization of battery cells is very important to ensure the consistent operation of a Li-ion battery for its application. In the present study, the OHP (Oscillating Heat Pipe) system is proposed as a battery cooling module, and experimental verification was carried out. OHP is characterized by a long evaporator section, an extremely short condenser section, and almost no adiabatic section. Experimental investigations were conducted using various parameters such as the filling ratio, orientation, coolant temperature, and heat flux. Average temperature of the heater’s surface was maintained at 56.4 °C using 14 W with 25 °C coolant water. The experimental results show that the present cooling technology basically meets the design goal of consistent operation.

2 July 2025 in Electronics
Verified
Journal Article
Open access
PDF file
SLSeung Hoon Lee
Seung Hoon Lee
SKSu-Jong Kim
Su-Jong Kim
JLJisu Lee
Jisu Lee
Seok-Ho RhiSeok-Ho Rhi
Seok-Ho Rhi
High-Bandwidth Memory (HBM) enables the bandwidth required by modern AI and high-performance computing, yet its three dimensional stack traps heat and amplifies thermo mechanical stress. We first review how conventional solutions such as heat spreaders, microchannels, high density Through-Silicon Vias (TSVs), and Mass Reflow Molded Underfill (MR MUF) underfills lower but do not eliminate the internal thermal resistance that rises sharply beyond 12layer stacks. We then synthesize recent hybrid bonding studies, showing that an optimized Cu pad density, interface characteristic, and mechanical treatments can cut junction-to-junction thermal resistance by between 22.8% and 47%, raise vertical thermal conductivity by up to three times, and shrink the stack height by more than 15%. A meta-analysis identifies design thresholds such as at least 20% Cu coverage that balances heat flow, interfacial stress, and reliability. The review next traces the chain from Coefficient of Thermal Expansion (CTE) mismatch to Cu protrusion, delamination, and warpage and classifies mitigation strategies into (i) material selection including SiCN dielectrics, nano twinned Cu, and polymer composites, (ii) process technologies such as sub-200 °C plasma-activated bonding and Chemical Mechanical Polishing (CMP) anneal co-optimization, and (iii) the structural design, including staggered stack and filleted corners. Integrating these levers suppresses stress hotspots and extends fatigue life in more than 16layer stacks. Finally, we outline a research roadmap combining a multiscale simulation with high layer prototyping to co-optimize thermal, mechanical, and electrical metrics for next-generation 20-layer HBM.

10 February 2015 in Journal of Electronic Materials
Verified
Journal Article
Closed access
PDF file
JJJu-Chan Jang
Ju-Chan Jang
RCRi-Guang Chi
Ri-Guang Chi
Seok-Ho RhiSeok-Ho Rhi
Seok-Ho Rhi
KLKye-Bock Lee
Kye-Bock Lee
HHHyun-Chang Hwang
Hyun-Chang Hwang
WLWook-Hyun Lee
Wook-Hyun Lee

8 December 2023 in Electronics
Verified
Journal Article
Open access
PDF file
IOIn Taek Oh
In Taek Oh
JLJisu Lee
Jisu Lee
JHJin-Se Han
Jin-Se Han
SLSeong-Woo Lee
Seong-Woo Lee
SKSu-Jong Kim
Su-Jong Kim
Seok-Ho RhiSeok-Ho Rhi
Seok-Ho Rhi
Lithium-ion batteries, crucial in powering Battery Electric Vehicles (BEVs), face critical challenges in maintaining safety and efficiency. The quest for an effective Battery Thermal Management System (BTMS) arises from critical concerns over the safety and efficiency of lithium-ion batteries, particularly in Battery Electric Vehicles (BEVs). This study introduces a pioneering BTMS solution merging a two-phase immersion cooling system with heat pipes. Notably, the integration of NovecTM 649 as the dielectric fluid substantially mitigates thermal runaway-induced fire risks without requiring an additional power source. Comprehensive 1-D modeling, validated against AMESim (Advanced Modeling Environment for Simulation of Engineering Systems) simulations and experiments, investigates diverse design variable impacts on thermal resistance and evaporator temperature. At 10 W, 15 W, and 20 W heat inputs, the BTMS consistently maintained lithium-ion battery temperatures within the optimal range (approximately 27–34 °C). Optimized porosity (60%) and filling ratios (30–40%) minimized thermal resistance to 0.3848–0.4549 °C/W. This innovative system not only enhances safety but also improves energy efficiency by reducing weight, affirming its potential to revolutionize lithium-ion battery performance and address critical challenges in the field.