Siavash Davoodi

Mr. Siavash Davoodi

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2019 in Water Science & Technology
Verified
Journal Article
Open access
PDF file
Siavash DavoodiSiavash Davoodi
Siavash Davoodi
BDBehnaz Dahrazma
Behnaz Dahrazma
NGNasser Goudarzi
Nasser Goudarzi
HGHajar Ghasemian Gorji
Hajar Ghasemian Gorji
This study aims to investigate the performance and mechanism of raw (R-ND) and saponin-modified nano diatomite (M-ND) in the removal of azithromycin from aqueous solutions. Adsorbent characterization was performed using XRF, BET, SEM, DLS and EDX. It was shown that the specific surface area of R-ND was 119.5 m2/g, 14-fold higher than that for raw diatomite, and for M-ND it was 90.1 m2/g. Various adsorption conditions, i.e. adsorbent dosage, pH, initial concentration and contact time were investigated. According to the results, despite reducing the specific surface area by 25%, modification of nano diatomite by saponin markedly enhanced its performance in the removal of azithromycin. The maximum adsorption capacity of R-ND and M-ND in the removal of azithromycin were 68 mg/g and 91.7 mg/g, respectively. FTIR results revealed that azithromycin was adsorbed by O-H groups on the diatomite surface. Weber-Morris intra-particle diffusion (IPD) model suggested that while IPD is not the rate-controlling step in high concentrations of azithromycin, it is the only step that controls the rate of adsorption in low concentrations. In comparison to R-ND, M-ND showed a higher efficiency in the removal of azithromycin and therefore, it can be used as a promising low-cost adsorbent to remove azithromycin from aqueous solutions.

10 April 2025 in Minerals
Verified
Journal Article
Open access
PDF file
Siavash DavoodiSiavash Davoodi
Siavash Davoodi
Bhabananda BiswasBhabananda Biswas
Bhabananda Biswas
Ravi NaiduRavi Naidu
Ravi Naidu
Sustainable strategies are required to mitigate elevated atmospheric CO2 levels. Achieving that by adsorption, especially by using clay-based adsorbents, drew attention. These are even more promising when these adsorbents are obtained by low-cost modifications. This study evaluates the effect of ball milling on the carbon capture performance of Australian halloysite nanotube (HNT)-rich kaolin samples: one without iron impurities (Hal) and the other with iron impurities (HalFe). The iron was mainly nested within illite/mica minerals in HalFe. Samples were ball-milled for 30 and 60 min, and their CO2 sorption was assessed at various pressures and temperatures. Crystallography, electronic microscopy, and surface area and charge characterization revealed reduced length and increased width of tubular structure following ball milling, leading to higher specific surface area without compromising crystallinity. CO2 sorption of Hal increased 14% at 20 bar and 15 °C after 60 min milling, with a ~300% rise at near-atmospheric pressures. Conversely, milling negatively affected CO2 sorption of HalFe, likely due to iron/illite-mica-related damage during milling. Crystallography, infrared, and thermographic analyses revealed physisorption as the primary sorption mechanism. Since direct disposal of CO2-laden materials is against sustainability principles, these materials were tested for methylene blue removal from aqueous solutions, achieving ~83% (Hal) and ~91% (HalFe) removal efficiencies. This highlights HNTs-rich kaolin clays’ valorization potential for carbon capture and utilization (CCU).

16 October 2020 in Water Science & Technology
Verified
Journal Article
Closed access
PDF file
HKHossein Khamooshi
Hossein Khamooshi
BDBehnaz Dahrazma
Behnaz Dahrazma
AEAli Ebrahimi
Ali Ebrahimi
Siavash DavoodiSiavash Davoodi
Siavash Davoodi
In this study, adsorption/desorption of vancomycin (VAN) on bentonite nanoparticles was investigated in a batch system. Adsorption experiments were carried out as a function of several influential parameters such as adsorbent dosage, pH, contact time and ionic strength. Bentonite nanoparticles were characterized by FESEM, EDX, BET, and FTIR analyses and the mesoporous structure was revealed. Langmuir, Freundlich, and Temkin isotherm models were applied for the examination of equilibrium data, and Langmuir was found to be the best fit. With the increase in pH and ionic strength, the adsorption capacity decreases which suggests the adsorption process may be dominated by the cation exchange mechanism. Moreover, VAN desorption from bentonite nanoparticles in two initial VAN loading was investigated under different concentrations of metallic cations of various valences (Na+, Ca2+, Al3+), and pHs 3–10. Desorption was strongly pH-dependent and the amount of VAN desorbed increased with increasing cations concentrations. The FTIR analysis before and after VAN desorption suggests that the formation of Al-VAN and Ca-VAN complexes on the solid surface and then their detachment from the solid surface may contribute to the higher VAN desorption by Al3+ and Ca2+.

3 February 2026 in Clean Technologies
Verified
Journal Article
Open access
PDF file
Siavash DavoodiSiavash Davoodi
Siavash Davoodi
Bhabananda BiswasBhabananda Biswas
Bhabananda Biswas
LWLaurence Noel Warr
Laurence Noel Warr
BTBalu R Thombare
Balu R Thombare
Ravi NaiduRavi Naidu
Ravi Naidu
Anthropogenic CO2 emissions have accelerated climate change, prompting the need for effective capture technologies. Adsorption using clay-based sorbents offers an eco-friendly alternative, although performance often requires enhancement. This study explored mechanochemical modification of two halloysite-rich kaolin clay samples—iron-poor (Hal) and iron-rich (HalFe)—using locust bean gum and quillaja saponin and compared their CO2 uptake with the calcined counterparts (CHal, CHalFe). All samples were characterized using standard techniques, and their CO2 uptake was measured volumetrically across 0.1–20 bar and 15–35 °C. Modified sorbents showed enhanced mesoporosity and binding sites, increasing CO2 uptake by up to 26% at 20 bar (11.85 mg/g) and 125% at 1 bar (2.25 mg/g). Calcination, however, reduced surface area and sorption capacity. Isosteric heat values remained within the physisorption range, as supported by FTIR, XRF, and XPS, which showed no bulk carbonate formation. These sorbents show lower CO2 uptakes than conventional ones. Yet their low costs, abundance, biocompatibility, and solvent-free synthesis indicate strong potential for large-scale applications, especially for low-pressure implementations such as landfills. Further detailed studies on kinetics, thermodynamics, and sorbent regeneration are needed. Spent sorbents can potentially be repurposed for subsequent use in other applications, e.g., water treatment, construction materials, thereby minimizing waste production and supporting circular economy principles.

25 June 2026 in Journal of Industrial and Engineering Chemistry
Verified
Journal Article
Open access
Siavash DavoodiSiavash Davoodi
Siavash Davoodi
Bhabananda BiswasBhabananda Biswas
Bhabananda Biswas
RNRavi Naidu
Ravi Naidu