Agricultural subsurface drainage systems are commonly installed on farmland to remove the excess water from poorly drained soils. Conventional methods for drainage mapping such as tile probes and trenching equipment are laborious, cause pipe damage, and are often inefficient to apply at large spatial scales. Knowledge of locations of an existing drainage network is crucial to understand the increased leaching and offsite release of drainage discharge and to retrofit the new drain lines within the existing drainage system. Recent technological developments in non-destructive techniques might provide a potential alternative solution. The objective of this study was to determine the suitability of unmanned aerial vehicle (UAV) imagery collected using three different cameras (visible-color, multispectral, and thermal infrared) and ground penetrating radar (GPR) for subsurface drainage mapping. Both the techniques are complementary in terms of their usage, applicability, and the properties they measure and were applied at four different sites in the Midwest USA. At Site-1, both the UAV imagery and GPR were equally successful across the entire field, while at Site-2, the UAV imagery was successful in one section of the field, and GPR proved to be useful in the other section where the UAV imagery failed to capture the drainage pipes’ location. At Site-3, less to no success was observed in finding the drain lines using UAV imagery captured on bare ground conditions, whereas good success was achieved using GPR. Conversely, at Site-4, the UAV imagery was successful and GPR failed to capture the drainage pipes’ location. Although UAV imagery seems to be an attractive solution for mapping agricultural subsurface drainage systems as it is cost-effective and can cover large field areas, the results suggest the usefulness of GPR to complement the former as both a mapping and validation technique. Hence, this case study compares and contrasts the suitability of both the methods, provides guidance on the optimal survey timing, and recommends their combined usage given both the technologies are available to deploy for drainage mapping purposes.
Peatlands constitute extremely valuable areas because of their ability to store large amounts of soil organic carbon (SOC). Investigating different key peat soil properties, such as the extent, thickness (or depth to mineral soil) and bulk density, is highly relevant for the precise calculation of the amount of stored SOC at the field scale. However, conventional peat coring surveys are both labor-intensive and time-consuming, and indirect mapping methods based on proximal sensors appear as a powerful supplement to traditional surveys. The aim of the present study was to assess the use of a non-invasive electromagnetic induction (EMI) technique as an augmentation to a traditional peat coring survey that provides localized and discrete measurements. In particular, a DUALEM-421S instrument was used to measure the apparent electrical conductivity (ECa) over a 10-ha field located in Jutland, Denmark. In the study area, the peat thickness varied notably from north to south, with a range from 3 to 730 cm. Simple and multiple linear regressions with soil observations from 110 sites were used to predict peat thickness from (a) raw ECa measurements (i.e., single and multiple-coil predictions), (b) true electrical conductivity () estimates calculated using a quasi-three-dimensional inversion algorithm and (c) different combinations of ECa data with environmental covariates (i.e., light detection and ranging (LiDAR)-based elevation and derived terrain attributes). The results indicated that raw ECa data can already constitute relevant predictors for peat thickness in the study area, with single-coil predictions yielding substantial accuracies with coefficients of determination (R2) ranging from 0.63 to 0.86 and root mean square error (RMSE) values between 74 and 122 cm, depending on the measuring DUALEM-421S coil configuration. While the combinations of ECa data (both single and multiple-coil) with elevation generally provided slightly higher accuracies, the uncertainty estimates for single-coil predictions were smaller (i.e., smaller 95% confidence intervals). The present study demonstrates a high potential for EMI data to be used for peat thickness mapping.
Subsurface drainage systems are commonly used to remove surplus water from the soil profile of a poorly drained farmland. Traditional methods for drainage mapping involve the use of tile probes and trenching equipment that are time-consuming, labor-intensive, and invasive, thereby entailing an inherent risk of damaging the drainpipes. Effective and efficient methods are needed in order to map the buried drain lines: (1) to comprehend the processes of leaching and offsite release of nutrients and pesticides and (2) for the installation of a new set of drain lines between the old ones to enhance the soil water removal. Non-invasive geophysical soil sensors provide a potential alternative solution. Previous research has mainly showcased the use of time-domain ground penetrating radar, with variable success, depending on local soil and hydrological conditions and the central frequency of the specific equipment used. The objectives of this study were: (1) to test the use of a stepped-frequency continuous wave three-dimensional ground penetrating radar (3D-GPR) with a wide antenna array for subsurface drainage mapping and (2) to evaluate its performance with the use of a single-frequency multi-receiver electromagnetic induction (EMI) sensor in-combination. This sensor combination was evaluated on twelve different study sites with various soil types with textures ranging from sand to clay till. While the 3D-GPR showed a high success rate in finding the drainpipes at five sites (sandy, sandy loam, loamy sand, and organic topsoils), the results at the other seven sites were less successful due to the limited penetration depth of the 3D-GPR signal. The results suggest that the electrical conductivity estimates produced by the inversion of apparent electrical conductivity data measured by the EMI sensor could be a useful proxy for explaining the success achieved by the 3D-GPR in finding the drain lines.