Various foaming agents can be used to achieve foaming of the precursors obtained by using the powder metallurgy method. However, the thermal behavior of pure aluminum precursors with different foaming agents has been studied very little in recent times. For the production of aluminum foams with closed cells, 1 wt.% of calcium carbonate (CaCO₃), titanium hydride (TiH₂), heat-treated TiH₂ and zirconium hydride (ZrH₂) were used. The foaming capability of the compacted precursors was investigated at temperatures 700, 720 and 750 °C. CaCO₃ and TiH₂ showed the best foamability at all considered temperatures, while ZrH₂ achieved relatively good foaming only at the highest temperature, 750 °C. Due to their low onset temperature of the decomposition compared to the melting point of the unalloyed aluminum, in hydride-based foaming agents the drainage occurred at the bottom part of the foam samples. Among the investigated foaming agents, precursors with heat-treated TiH₂ had the worst foaming properties, while CaCO₃ showed the best foamability without the occurrence of drainage.

The choice of foaming agent and its mass fraction significantly affect the size and number of metal foam cells. The powder metallurgy process was used to produce aluminium foams with the addition of various foaming agents: titanium hydride (TiH₂) and calcium carbonate (CaCO₃). TiH₂ was added in an amount of 0.4 wt.%, while the quantity of CaCO₃ varied between 3 and 5 wt.%. The produced foams, with approximately the same degree of porosity, were scanned using a non-destructive computed tomography method. The number, size, equivalent diameter, sphericity, and compactness of cells were analysed on the obtained three-dimensional models. The results showed that foams foamed with TiH₂ have much larger cells compared to CaCO₃ agent. By considering the influence of CaCO₃ fraction on the morphology of aluminium foam, it follows that a smaller quantity of CaCO₃ (3 wt.%) provides a macrostructure with smaller cells. Samples with five wt.% CaCO₃ contain slightly larger cells but are still much smaller than foams with TiH₂ foaming agent at the same degree of porosity. The sphericity and compactness indicate that TiH₂ foaming agent forms cells of a more regular shape compared to CaCO₃ agent.

The heat treatment of aluminum alloys is very important in industries where low weight in combination with high wear resistance, good strength, and hardness are important. However, depending on their chemical composition, aluminum alloys are subjected to different mechanical and thermal treatments to achieve the most favorable properties. In this study, an Al-Zn-Mg alloy was heat-treated including solution annealing at 490 °C for 1 h with subsequent artificial aging at 130, 160, and 190 °C for 1, 5, and 9 h. The hardness (HV1) and abrasive wear resistance with three different abrasive grain sizes were measured for all samples. The highest hardness was measured for the samples artificially aged at 130 °C/5 h, 227 HV1, while the lowest hardness was measured for the samples aged at 190 °C/9 h. The highest and the lowest wear resistance was also observed for the same state, i.e., artificially aged at 130 °C/5 h and 190 °C/9 h, respectively. The critical abrasive grain size was detected for some samples, where a decrease in wear rate was observed with an increase in the abrasive grain size from the medium value to the largest. The Response Surface Methodology (RSM) was applied to demonstrate the influence of the input parameters on the material wear rate.

This paper presents the results of wear tests of two types of commercial low-carbon, low-alloy martensitic abrasion-resistant steels, Hardox 450 and XAR 450, which belong to the hardness class 450 HBW. These steels, due to their increased resistance to the abrasive wear mechanism, are used for machine parts for applications in intensive abrasion environments such as construction, mining, and agriculture. The scope of work included microstructure analysis on an optical microscope, chemical composition analysis, Vickers hardness measurements at different loads (HV0.2, HV1 and HV2), and wear testing. Wear tests were carried out by the standard method “dry sand—rubber wheel”, and tests on the Taber abrader device. Microstructure analysis revealed that both steels have a similar non-oriented, homogenous, fine-grained martensitic microstructure. The results of HV2 hardness measurements showed a similar trend for both steels in all examined sections of the plates. For both tested steels, the hardness values of HV0.2 and HV1 are slightly higher than HV2, but the scattering of the results is also greater. Abrasion resistance testing using the standard “dry sand—rubber wheel” method showed that Hardox 450 steel has a lower volume loss of about 8%, but a greater scattering of the results compared to XAR 450 steel. The results of the abrasion resistance test on the Taber abrader device confirmed approximately the same behavior. For both steels, a prediction model was established for a reliable assessment of the wear intensity concerning the grain size. Although examined steels belong to the same hardness class, Hardox steel seems to be a more appropriate choice for the manufacture of machine components exposed to abrasive wear.