Limitation and inequality of water in interspace and time opposite to the increased water demand indicated from the density of headwork nodes in the river system. It requires proportional-equal water allocation determined by the model. Existing models are not based on water as a public good and not using the sustainability-efficiency-equity criteria despite irrigation is the biggest use. The Water Allocation Model Equalization or in Indonesian it is called “Model Ekualisasi Alokasi Air” (MEQAA) is proposed. MEQAA modeling system is inspired by the shortage of irrigation water for a quite extended period of time and the complexity of the water allocation system in the Lombok river basin. MEQAA is assisted by MS Excel-VBA 2016 that can be tracked automatically on an independent river system scheme to create a network equation with mass balance principle and operation rule. This model is based on the dynamic-deterministic, so the performance test can be used with synthetic data. This experiment was compared with the output from the equalization method and the “first-come, first-served” (FCFS) method. The conclusions of this experiment are: (a) MEQAA can build a specific model according to a network-flow configuration for optimization-simulation with iteration of K-factor (release portion) and C-factor (storage portion) in order to get a maximum and equal and (b) the FCFS method can be detrimental to the river system. MEQAA is suggested as a decision support tool for water allocation planning or real-time operation.
25 July 2016 in Jurnal Teknologi (Sciences & Engineering)
The stepped spillway has increasingly become effective energy dissipation. The stepped spillway has been accepted to be the most powerful hydraulic structure to dissipate large flow energy downstream from spillway crest. The steps act as roughness elements significantly increase the dissipation energy rate. The physical study has performed on flat and pooled stepped spillways with a slope spillway (θ = 45˚) and number of steps (N): 20 and 40. The experiments were conducted for ten Froude number (Fr) run ranging from 1.117 to 9.909 with 0.700<yc/h<3.00. The focus of research to investigate the relationship between relative energy losses in skimming flow performance against Froude number on various stepped. The effect of number of steps is evident when the relative energy loss increases with the number of steps. In addition, the relative energy loss of flow on pooled steps is dissipating more energy than flat steps.
2 February 2024 in Journal of Law and Sustainable Development
Purpose: This research intends to examine inclined pile structures to analyze the effectiveness of inclined pile structures by analyzing the relationship between the transmission coefficient and wave steepness based on several parameters including pile slope (α), the distance between the piles in one row (D), distance between the top of the piles (b), depth (d), wave height (H) and wave period (T). Theoretical reference: Wave breaking structures are widely used to protect beaches from the impact of sea waves that propagate to coastal areas. Wave breakers are coastal structures that are used to withstand and break the height of waves coming towards the beach, so that the area behind the breakwater does not receive much influence from the waves. When passing through coastal buildings, the waves will be reflected (reflection) and forwarded (transmission). Method: Physical laboratory simulations have been carried out to obtain wave data interacting with the inclined pile structure. Next, energy spectrum analysis was carried out to determine the energy spectrum of incident, reflection and transmission waves from wave probe measurements in the form of time series data. Each energy spectrum is used to see the reflection and transmission capabilities of the pile structure from the reflection and transmission coefficients. Result and Conclusion: From this research it is known that in general Kt has an inverse relationship to wave steepness value (Hi/gT2 and Hi⁄ L). The most effective water level for this breakwater is the average water level. The most effective spacing scenario is α=600 scenario; D=1.69cm; b= 5 cm with a Kt value of 0.652 at Hi/gT2 of 0.006, Kr= 0.103 and Kd= 0.245, so only 65.2% of the waves can pass through the structure, 10.3% is reflected, and 24.5% is removed. Implication of research: These lost waves can be caused by waves traveling through the inclined pile structure, due to collisions between waves or other things. Originality/ value: One of the wave breaker innovations that are being developed is the pile structure. Currently, a lot of research has been carried out regarding upright pile structures.
The land use characteristics in the Semantok watershed have a significant impact on the reservoir's usable age. According to the land use patterns, including teak woods, rice fields, moorlands, dry fields, and residential areas, the Semantok watershed has the capacity to carry sediment when it rains. One of the models to analyze surface runoff and sediment is the Soil and Water Assessment Tool (SWAT). SWAT was developed to predict the impact of land management practices on water, sediment and agricultural chemical yields in large complex watersheds with varying soils, land use and management conditions over long periods of time. The purpose of this research is to quantify the amount of erosion and sedimentation that results from land use changes in the Semantok watershed in 2015 and 2021 and to determine management scenarios that can reduce the value of erosion and sedimentation that can implemented upstream of the Semantok dam using SWAT. The data used for the research are climatology data, DEM map, landuse map, and river data. The amount of erosion at the Semantok watershed outlet increased from 7.00 mm/year in 2015 to 14.18 mm/year in 2021. Based on Forestry Ministerial Regulation No. P.61/Menhut-II/2014, the Semantok watershed's carrying capacity is 3.95 falling into the pretty bad category (3.5 < DDD < 4.3). Three scenarios were compared in order to carry out control efforts: revegetation, check dams, and combining revegetation and check dams. The most efficient way to reduce erosion by up to 30.51% is to combine revegetation and check dam.
1 December 2017 in Journal of Water and Land Development
As a type of gate that is used to control the water level upstream, sluice gate is the gate with simple shape and outstanding ability to flush the sediment. The operation of the gate is considered an important process. The up and down movement of the gate would affect the velocity and cause local scour as the result of fluctuating rate. This research aims to assess the effects of discharge and gate-opening height variations, as well as the type of bedchannel material, on the change of depth of scour (ds). The research was conducted of open channel flow model with a sluice gate able to up and down movement. The discharges used in the research were 9 types ranging from 1.0 to 5.0 dm3·s−1. There were 5 variations in the height of gate-opening ranging from 0.5 to 2.5 cm at intervals of 0.5 and types of channel-bed material. The results of the research showed that the depth of scour can be analysed as a function of discharge, height of gate-opening, height of water level upstream and downstream, and the type of bed material used. The scour depth equation on is $d_s = 1.7822\left( {{Q \over a}} \right)^{1.1347} a$ . Calculated coefficient of determination of the relationship between two types of channel-bed material and the depth of scour was R2 = 0.946. Consequently, it can be concluded that the equation can be applied on both types of bed-channel material.
1 March 2020 in Journal of Physics: Conference Series
The head loss in the nonlinear bend caused by the friction of the wall along the bend and the direction change of the flow due to suddenly angle change. The essential elements include velocity (U) number of slices (n), length of the average slices wall (Li), angle change (α), friction coefficient (f), acceleration of gravity (g), and slope of the pipe base (S). Based on equation 12, with fixed discharge, the bigger diameter, and more number of slices in used, then the smaller head loss. Conversely, if the diameter used is getting smaller and less the number of slices, then the head loss bigger. This analysis is expected to provide optimal benefits for activities related design to piping networks, especially main networks that use large diameter pipes. Especially piping networks with the use of steel pipe or High-Density Polyethylene pipe materials. Such as oil pipes, gas pipes, and freshwater distribution pipes. The head loss that occurs will more measurable, fast, easy, and economical in implementation.